Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi,
I am working with two nRF52840 DVKs and the 802.15.4 example "wireless uart" from the SDK v15.2.
I flash both boards, and both of them get initialized (LED1 ON). Then...
We program the nRF52840 with a Segger tool at 8MHz.
The programmation time for 400kB is 13s (0.5 erase, 2.3s soft device and 8s application).
When we reduce the frequency...
The customer's goal is to play a tone on an external speaker with a data rate of 11.05KHz.
The "default" demo code for the Thingy52 @ https://github.com/NordicSemiconductor...
Hi all,
I just migrated from sdk 14.0 to sdk 1.52, and now I'm running into a problem while testing my codebase with ceedling. When testing my delay module, which uses nrf_delay...
Good morning,
We are making our first PTS test to certyficate our BLE device. I have question regarded to test name GAP/DISC/NONM/BV-02-C. Our LE device plays the Peripheral...
Hi:
I download nordic example.But i can not know how ZBOSS zstack form a network.
I try to use bdb_start_top_level_commissioning(ZB_BDB_NETWORK_FORMATION ) and it can...
Hi there,
I'm just beginning BT development, so sorry for my basic question:
Our application needs to transfer data from PC to our device (approx. 512 bytes) then our...
Hi
I have tried to enable bonding on a application based on the Running Speed and Cadence example (Both peripheral and central). (I could not find an example with bonding...
I want to send data from Nrf52840 dk. I want to receive the data sent on nrf24l01, which is connected to the Arduino Uno card. So I want Nrf52840 to communicate with Nrf24l01...
Hi,
downloading works fine now from SES. But now I like to use some of the ANT example projects. Im told to install SoftDevice package before downloading the example firmware...
I'm modelling a complex system with multiple BT devices based on the NRF52 using a very detailed model of the RF.
The system is based on the NRF52 using the mesh stack to...
Hi everybody!
My goal now is to use nRF52832 as a intermediary for an update package. In other words, my goal is to send a file (probably .zip package) to a board and save...
Hi,
When running the unit tests for Mesh SDK 3.1.0 I get the following failures.
83/92 Test #83: generic_dtt_client ...............***Failed 0.00 sec
From the log I...
Dear DevZone,
I'm new to the nRF52-DK and Nordic in general. I'm trying to set up an nRF52-DK to use with nRF Sniffer, and not having any success.
I have tried following...
