But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I have 3 nrf boards connected. 2x nrf52832 and 1x nrf5340.
esb_tx is running on nrf52832(682782977) esb_rx is running on nrf52832(682497942) & nrf5340(1050025410)
west...
Hello
I have a custom nrf52840 board with an external 1MB NOR flash
The app uses MCUboot for DFU
I know I can define the external flash in the pm_static.yml for the...
We are currently working with the nRF52832 Development Kit and are aiming to interface an ISO15693 NFC reader using the PN7150 NFC module. We intend to communicate with the...
Are there any serial commands that I can use to control some the functionalities of the board. My task is to use the dk with a windows app (UWP, C#), I want to start stop...
I tested it on the lzma example (ncs\v2.8.0\nrf\tests\subsys\nrf_compress\decompression\lzma),on the Cmakelist.txt code
generate_inc_file_for_target(
app
${ZEPHYR_NRFXLIB_MODULE_DIR...
We have a production system running a modified asset_tracker_v2. Things are basically running fine but there is question with downlink and FOTA operations. We publish a JSON...
I am trying to get mcuboot working on a custom board. on version 2.7.0 sdk, But the board is not found.
I have simplified it to a minimal version like so (my folder can...
I am evaluating external flash on nRF5340DK. When I'm doing appcore DFU from external flash so that mcuboot_secondary and settings_storage are located on external flash, everything...
Hello!
I am returning to software development for a BLE Mesh project on the NRF52840 after being focused on the hardware development for several months. I see that NCS is...
Hello
I am evaluating Wi-Fi location using the nRF7000 and nRF9160.
For the initial test, I used the nRF7002 Expansion Board. I soldered wires to it and connected them...
What would be the certification cost for developing small volume Zigbee or Matter+Thread applications using nRF modules and nRF Connect SDK? Is this eligible to certify via...
Hi experts,
I followed the instructions the Readme file described. It almost works well. But I still found two issues:
the Startup time is too long when pressing the...
Hello!
I am currently using the nRF7002DK, and I am interested in utilizing the nRF5340 MCU as a slave SPI with an external MCU that supports 3.3V SPI voltage levels. My...
hi
board : nrf52840 custom board
sdk : nrf connect sdk v2.6.1
example: matter light bulb
problem:
After the code is burned in, the system not working, I have modified...
