After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi, I have developed my own custom module with a program based on the NUS example.
I wanted to use the dongle as a configurator (in the sense that i connect it to the usb...
Hi:
My device is nRF52833-QDAA. And I'm totally a beginner in RF.
Right now I'm trying to figure out the component value of the matching network Z1 Z2 Z3 .
How can...
After problems with the programmer I have successfully flashed simple custom board with ACN52840 module, but the unit does not resetting after flashing using J-Link Pro. Starting...
Hi,
I have a project where I use nrfx_saadc and need to change channels and simple/advanced mode in runtime
If I start with simple mode, samples, move to advanced mode...
The note in https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.5.0/nrf/security/tfm.html#overview reads: "Support for TF-M with minimal version disabled in nRF Connect...
Hello,
I flashed the audio application as left headset on my audio DK, but whenever I connect it to my mobile phone, the device isn't shown in the media output list.
Yes...
When using the nRF5 SDK v17.x development environment, the BLE MAC address can be retrieved using:
This will return the assigned MAC address (eg. from the nRF52840 on...
Hello,
I am currently working on a project using the NRF52 SDK and Segger Embedded Studio. I need to set up a password (or passkey) for securing the Bluetooth connection...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
I am trying to use the device name as...
I'm developing a linux device driver for nrf7002 and adding softap support. From the Nordic Playground driver it looks like there is no current support, but a lot of the cfg80211...
Hi, when I run the MQTT sample as is, I'm having problems with the TLS and port configuration. The terminal output is:
That looks correct, but on closer inspection the...
Hi!
I'm getting this error in nRF Cloud when using a nRF9160DK connected by LTE-M to the network:
Device sometimes sends some data correctly but, after few minutes i...
Hello everyone,
I have a custom board with a NRF52840 microcontroller with 32MHz crystal oscillator, running Zephyr RTOS with NRF Connect SDK and want to make use of a hardware...
I have a custom board with a nRF52832 QFAB at its center, and I want to program it via a nRF52-DK. I have created a custom board directory and have initialized a few led pins...
I see there is a way to set an audio event exceeding a set threshold. https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_thingy53%2FUG%2Fthingy53%2Fhw_description%2Fmicrophone_buzzer...
