Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,nordic teams
im develop a keyboard use nrf52840 by ncs sdk 2.6.when i test the dfu funcation by python file ,there is 2 problems .
1.the usb dfu is so slow that i need...
I want to add a custom at command in the SLM example . I follow the https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.6.1/nrf/libraries/modem/at_cmd_custom.html , enable...
Hi.
I have a problem.
I changed project settings 52832 -> 52840
on 52832 the project work perfectly.
using 52832, SDK 15.3.0 S332, ble, ant, ble dfu.
now I wanna...
I use one channel of the SAADC on nRF52832 to measure the power supply voltage. Code for configuration & operation of SAADC attached:
Short description:
- Configure...
Hello and thank you for your time. I seem to be getting some incorrect performance from the flash memory with NVS, in that NVS needs to be primed or something before it works...
Hi,
I'm working on a board that uses an npm1100 (QFN) in the following configuration:
When testing my board, I populated it with only the components shown in the...
Debugging my application indicates that I might be not servicing BLE NUS RX frequently enough bt_nus_cb.received is sometimes not called timely Is there any way for user to...
Hello all,
I'm using a custom nrf52840 dongle. There are some questions about bootloader and Softdevice. Everything works fine when I use nrf Bluetooth Low Energy app...
Hello.
I have a product that I am working on which a peripheral and it is able to communicate test data over BLE UART connection. For development purposes, we have internally...
Hi Team,
I have 1 nRF5340 Audio DK. With the steps mentioned in below links, I configured Json file to Gateway and I'm able to achieve it. ( developer.nordicsemi.com/.....
Hi,
We are developing on a nRF52832 MCU and we tried to enable MPU on the whole RAM region (addr: 0x20000000, size : 0x10000) But when we create a new MPU region around...
Hi,
So I have seen there is a clean -up option to set the architecture core HW registers to their warm -reset values as specified by the architecture before running the...
Hello everyone,
using Segger Embedded Studio, I encountered an issue with the TWI libraries. My device consists of a custom PCB controlled by the nRF52840 (programmed with...
A simple and maybe trivial question. When in a thread I wait data for example with
is it like call continuously the k_yield()? How the api above works in the underhood...
