Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I'm moving an application from NCS v2.0.2 to NCS v2.1.0
Everything compiles properly in v2.0.2.
I think I've converted all of the pin definitions properly from the v2...
Hello,
we are using nRF9160 as Bluetooth host together with the Mcumgr Gatt service. We would like to be able to perform FMFU update using the Mcumgr library. We have verified...
Hi:
After downloading the sdk, I installed the compilation environment on my laptop and successfully compiled the at_client project. However, after the same installation...
I want to implement a sophisticated peripheral that implements a keyboard, mouse, and raw HID interface via USB and BLE.
I haven't found composite HID examples for USB or...
Hi,
When I try to build the ESPI sample using west I'm getting the following error:
Can you please let me know what the error is? I tried looking up the issue, but couldn...
Hello Nordic Team,
While going through this page on peripherals used by Softdevice https://infocenter.nordicsemi.com/topic/sds_s140/SDS/s1xx/sd_resource_reqs/hw_block_interrupt_vector...
Hi guys,
I want to send 'a' characters via the uart1 of the nRF52840-DK. I cut the short on the SB6 jumper to disconnect LED 2 from P0.14, which also happens to be TX of...
Hi DevZone
I just want to ask if one can use the nPM1100 with the unregulated output to the nRF9160 (which can take 3-5.5V), and the regulated output the other peripherals...
We try to get audio samples form analog or digital MEMS microphone to nrf54840 RAM memory with low power consumpion at 32kHz rate. We consider to use internal SAADC, PDM or...
hi, I want to use PPI function for timer trigger GPIOTE,
when timer interrupt comes, my output pin will toggle, but I find my code doesn't work, I think it is GPIOTE mistake...
I am trying to run the nrf/samples/bluetooth/peripheral_lbs example for the nRF5340-Audio-DK using nRF SDK v2.1.0. I am using the following command to run the example:
west...
We have a product on the market that uses the nRF24 and a PIC, chosen primarily for it's cost and rapid development time. We are now looking into using a nRF52 to replace...
My system details:
Ubuntu 20.04.04 LTS
Visual Studio Code 1.70.2
NCS 2.0.2
nrfutil version 5.2.0
Toolchain Manager v1.1.3
I'm trying to build my project, but...
Hi,
I'm developing my log system in a project with a secure partition with TF-M. I am following this log system design document . In my project I have, as a test, the following...
For nrf52840 which is the option for L3 Inductor. In current market L3 is obsolete. Part Number is HK100515NJ-T i need option. Also crystal capacitor part is needed.
