Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi
I try to use in a mesh topology. I decided to send a string from client to nodes and receive its response. but I don't know how apply that. please help me to choose an...
hi , we have a nRF52840 DK when connected to PC via J-link there LED5 blinks . when i try to flash the code using Kiel IDE
get this error
using nRF connect the device...
Hello DevZone,
On my board I have a nRF52810 and a nRF52840. I want to implement a serial bootloader for the nRF52810 and have the nRF52840 program it.
I have looked...
Hello All,
We've got a new design using the nRF9160 - most of the PCBA's are connecting just fine to LTE-M - but I've seen a few with 'erratic' connections to LTE-M - I...
Hi, I can successfully build the openthread-cli sample but fail with all matter samples
Please refer the following log
> Executing task: nRF Connect: Build: light_bulb...
Hi
I'm just starting out to test the nRF9160 DK board and have just flashed the NB-IoT Asset Tracker as per the introductory video uploaded by Nordic here:
https://www...
I use a nRF9160DK for make my experiments:
nRF9160(modem) -> mdm_1.3.2
nRF9160(application) ->Serial Modem LTE (nRF SDK 2.0.0) with UART 2 and CONFIG_SLM_NRF52_DFU_LEGACY...
Dear Support Team，
Based on NCS 1.9.1, compile and download Hello Word firmware to nRF5340-DK (1.0.0), measure the voltage of all IOs with a multimeter as shown below: ...
After I ported my project to ncs2.0.0, I found that the RX of nrf9160 could not receive data. To this end, I modified at_client for testing and found the same phenomenon....
Hi All,
Later I will build a Custom Service, so I refer to ble_app_blinky.
According to the image below, I cannot clearly understand the difference between the two from...
I recently encountered a MCU crash problem. I think it is related to NRF_ LOG_ Process (). I used the simulation to catch the following scenarios. MCU crashes at this time...
Hi all:
SDK17.1.0
softdevice:s112
example:ble_app_hids_keyboard
I add a lot of function in my project ,including gzll, i2c,timer1 ,app timer ,rtc ,flash read/write...
Hi,
We are troubleshooting high power consumption on a custom nRF52832 board. It has taken us down to just
1. Enable RTC,
2. Setup GPIOs,
3. With and without NRF_POWER...
I am currently experiencing an issue using MCUmgr CLI over a serial connection provided by the on-board J-Link debuggers on nRF52 devkits.
When using MCUmgr CLI to send...
Hi,
currently I'm testing several options to transfer data in broadcast manner, i.e. in fact extended advertising due to the amount of data to transmit. A few days ago,...
