Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi,
We are looking to purchase the nRF52833 DK. The data sheet says it supports an RX sensitivity of -95dBm. Does it not support up to -103dBm as quoted on the data sheet...
Hey,
I would like to know if its somehow possible to rebond if the central device (nrf52) has deleted the bonding information about a device and then this deleted peripheral...
I'm trying to implement a timer with 1ms resolution that my application can use externally using a callback function.
The idea is to
Implement the timer as a 32-bit...
Hi all,
I need to upgrade an nRF52 device with SoftDevice 5.0.0 and bootloader.
I have to upgrade from SD 5.0.0 to 7.2.0.
I use this command to generate the zip file...
Dear all,
I have some problem with SPIs co-work.
I enabled two SPI instances in this project.
SPI Instance 1 function(non blocking mode - DMA enabled, 4Mbps): reading...
Hi there, Thanks in advance for your time and attention. We started to see some cases where our devices boots and gets a NO_PAGES error after having been turned off(or at...
I try to simulate system hang by adding while(1) after calling watch dog feeding function. But watchdog event handler _wdtEventHandler() isn't called.
int main(void) { ...
Hi,
I am currently trying to read the GPIO latch register in my Zephyr NRF SDK 1.9.1 C++ project with the following line:
This is resulting in the following compile...
I have downloaded the nRF connect for PC and successfully managed wo work with the dongle using the BLE General tool but when I tried to use the power profiler tool probably...
Hello Nordic Team,
I have a nRF52833 DK and I am running Light switch Server and client applicaiton in it.
I am in the moment customizing the application for our custom...
Is there a way to disconnect from devices that have exceeded the maximum number of connections allowed?
I am developing with nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral...
When I want to implement my edge impulse model to my nrf5sdk code using vs code I found this errors,
Terminal will be reused by tasks, press any key to close it.
> Executing...
I've just updated my nRC Connect SDK from V1.9.1 to V2.0.0. I did this via the nRF Connect for Desktop Toolchain manager. I'm using the nRF Connect extension in Visual Studio...
Hello everybody,
i currently develop two devices, one master and one slave (sensor). Both devices have the dfu service completly working.
My problem is that the master...
Hi
I am trying to FOTA download with AWS S3 bucket.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/nrf/libraries/networking/fota_download.html I am using HTTPS...
