Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hello support team,
I have two development kits: one nRF5340 DK and one nRF5340 AUDIO DK .
On the nRF5340 AUDIO DK , I have flashed the unicast server example. Now, I...
We are working on a project where 802154 radio runs on the NetCore. The NetCore firmware is based on the multiprotocol_rpmsg example by Nordic. Additionally, we have a custom...
SDK : NCS v2.8.0
SoC : nRF52840
HW : custom board
Hello,
I was trying to use settings subsystem, and I managed to make setting_write() and settings_read() work....
Hello, our entire code base is built around the Nordic SDK. We are considering designing a system that uses an nRF52840 as its controller but has no wireless functionality...
Setup: The nRF52840 DK is running the peripheral_hids_keyboard sample project. The device is connected to a macOS host, showing expected functionality.
Problem: When the...
Hi, We are using an nRF5340 and nRF Connect SDK v2.6.2. We have set CONFIG_BT_BUF_ACL_RX_SIZE to more than 251 and BT_CTLR_DATA_LENGTH_MAX to 251 in our prj.conf.
W hen...
my program works on the nrf52840 DK but does not work on the custom board using nrf52840-QFAA. We are using nrf sdk V2.8.0 running zephyr. Program is attached.
What to do...
Hello,
Version - nrf Connect SDK v2.7.0
The background to the system I am developing is described here and here
In short, I have an application containing a BLE Peripheral...
Hello everyone, I hope you have a good days. I'm developing an project for military standards. I'm using Nexys 4 DDR FPGA ev. board and VHDL language. My question is how can...
NCS 2.6.0, nrf52840
On our board we have attached a QSPI nor-flash as well as a SPI-based OLED display on the same pins.
I'm wondering if there has been any attempt...
In my application, I have implemented Serial Recovery. The interface used for the transfer is UART0 , which I also use in my application at a baud rate of 1M. When I enter...
I'm struggling to get a peripheral device to work with two simultaneous connections. I have attached my configuration (for the application) and my connect/disconnect callbacks...
Good morning team,
As the nRF7002 has been certified Wi-Fi 6 and registered by the Wi-Fi Alliance, can devices embedding the nRF7002 use the Wi-Fi logo and the Wi-Fi designation...
Good morning Nordic support,
I'm a beginner with the nRF Connect SDK and the nRF5340 microcontroller.
I'm using SDK v2.9.0 (the latest available for my Mac).
I started...
