After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hello,
I am using th PCA10040 board, and I can build my project without problems. But when I debug it, 'stopped by vector catch' error appears. I have been reading possible...
hello Nordic
i am working with nrf52840, with zephyr (i am new to zephyr)
i have an issue with not responding pin interrupt so i try to run zephyr example to see how...
nRF9160 DK NCS v1.6.0, SLM with:
CONFIG_SLM_GPIO_WAKEUP =y
CONFIG_SLM_INTERFACE_PIN =24
Sometimes after at#xsleep=0 and several pulses on pin 24 SLM wakeups with...
Hi. I'm testing the multi-image DFU in nRF Connect SDK 1.7.0. I'm seeing an issue with the firmware images not getting reverted when it should.
Here's what I'm doing:
...
Hello!
I am having unexpected issues in setting TX power using Softdevice call to SD_BLE_GAP_TX_POWER_SET via sd_ble_gap_tx_power_set. Please see the code below.
The...
I am developing with 52840.
We checked button-related problems while using the source that checked the behavior on the DK board on the adafruit-circuit-playground-bluefruit...
hello Nordic
i am working with nrf52840, with zephyr (i am new to zephyr)
i have an issue with not responding pin interrupt on an input pin
this is my trigger pin...
The following code works perfectly fine every single time if i use NCS 1.5.1..we decided to move to 1.6.1 recently, and while we were able to get everything else working,...
Hello I'm making a custom usb device class with 1 IN & OUT Bulk endpoints running on a nrf52840 with 340. The device reads the data correctly that are being sent by the host...
Just no clue on including the proper files, initialization and how to use API in main or handler. My intent is once a led is on trigged by a button pressed up from the other...
I am trying to develop a peripheral targeted for mobile devices that can either behave as a touchscreen (several simultaneous contact points, useful for performing gestures...
Hello
I wanted to use the MQTT simple example (which works great) and add timer, so that MQTT will be send every 20 seconds:
on main I added:
struct k_timer my_timer;...
Good day!
This function in scheduler server compares timestamps only between each other and if scheduler stores settings after reset and set new time (without bt_mesh_scheduler_srv_time_update...
Hello,
I am struggle with an issue. When I enable the BLE on an nrf52833 and try to write on the internal flash with LittleFS, my flash get corrupted. I try without enable...
I am using nrf5340DK with sample 'Bluetooth: HCI RPMsg' and try to execute some HCI commands on it, but not getting any shell of 5340DK. As I know in case of dongle we can...
