Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi
Currently we were looking for buying Laird 451-00004 dongle to be used with PTS software. Since the device is not available with any of the distributor. we are approaching...
chip:nrf52840
SD:S140 6.1.0
SDK:nRF5 SDK v15.2.0
ASSERTION FAILED often appears in my firmware, connecting J-link in debugging state or turning on NRF_LOG and outputting...
Hello, I am using FDS to store three int32_t numbers. Here is my code for storing :
Here is my code for reading :
Here are the logs (stored values are the correct...
I'm having trouble sending more than 256 bytes over TWI.
nRF52840 SDK17.0.2
Used Function :
I have to send 8,208 Bytes continuously through the TWI interface in the...
Hello,
I'm trying to establish a connection with my own MQTT brocker on MQTT Box. I change the config on the prj.conf and on Kconfig file, like this :
But when i rebuild...
I downloaded the CIAA Layout and BOM resources from this page: (1.0) https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF52832/Download#infotabs . I opened...
Hello there,
I cannot manage to activate my SIM card. Can I get some help?
* Tried outside of my company firewall? Yes, to no avail.
* Tried entering only the first...
When NRF52832 as SPI Slave, how can I know how many bytes the slave should read,the API nrf_drv_spis_buffers_set(&spis, m_tx_buf, length, m_rx_buf, length)),does not have...
Hi guys,
I am now facing a problem that I can't stop the pwm by using nrf_drv_pwm_stop.
Here's my initial code for pwm and start the pwm in the while loop.
The output...
Hello, I've tested multiple NB-IoT cards from China Mobile using the asset tracker on nRF9160 DK. The NB on Band 8 ( AT%XCBAND returns %XCBAND: 8) has no issue connecting...
I first assumed the obvious that the first library would be used with the (Visual studio) multi-threaded DLL/MD option and the second would be used with the multi-threaded...
Hi,
Currently we're developing RGB bulb which has mesh feature (nRF52832). So this done by using nRF5 SDK 15.2.0 and Mesh SDK 3.0.
We're able to control all three channels...
Hi Team
I would like to store a simple integer value in flash and read it back after a power cycle. I already studied the library Flash-manager of the nRF5 SDK for Mesh...
Hello, I'm trying to flash custom developed beacon based on nRF52811 and everytime i try to flash i'm always greeted with an error "Failed to write memory" i have attached...
