We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I'm developing a system of nRF9160, nRF52832 and Iridium 9603 (satellite modem) - all on the same main board. The nRF9160 is the brain of the system and handles LTE, GPS and...
Hi,
I am new to working with nrf52840 devices. I am wondering if it is possible to change the transmission power of packet during transmission several times such that some...
I wanted to increase the bandwidth of bluetooth using the following example, but there is a limit of only 1 board.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v17...
project : zephyr
controller stack : zephyr stack
description ： we start direct adv using our DK，and we want it send broadcast only once。 but zephyr stack send adv all...
Hi,
I am working on NRF52 series (NRF52 DK and NRF52832) and would like to know whether it is possible to use Bluetooth 5 extended advertising capabilities to send, let...
Hi there, I'm routing the nrf9160 to a STM32 and I need to know the pinout for COM port used.
On my PC, I know COM11 is the one that is used for AT Commands
But, I...
Hi,
I'm using NRF52840 with direct test mode application.
I'm sending to the function dtm_cmd following parameters: 0x4000, 0x8000, 0x9400, 0xA500.
I understand...
Hi,
After suspending task in a specific code line (using vTaskSuspend) and resuming the task (using vTaskResume)- will the task continue from the specific suspension line...
I am going to make a project with nRF52840 In my application, I need to send sensor data to Raspberry Pi I noticed this tutorial and tried to implement this in my project...
i tried to implement radio notification in order to change advertising data but i had this error
when i put the periority to LOW i get this error, if put MID or HIGH the...
What benefit is there to RX gain for the bluetooth front end module
Most other 2.4 amplifiers do not have RX gain.
Our concern is the noise floor, would not the RX gain...
Hi Sri,
When referring to this ink , we know the typical and max ripple values are 70 mV and 100 mV respectively at REGOUT0=1.8V.
Two questions:
1. Do we have the...
I am attempting to add peer manager bonding and whitelisting to an existing app.
The app is simple, uses nordic uart services to pass 4 bytes of data between two embedded...
I am currently using nus and dfus service. It works fine. The secure DFU service is displayed in the nrfconnect app.
However, when ble_bas_enable, the duf service disappears...
