This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I am attempting to add peer manager bonding and whitelisting to an existing app.
The app is simple, uses nordic uart services to pass 4 bytes of data between two embedded...
I am currently using nus and dfus service. It works fine. The secure DFU service is displayed in the nrfconnect app.
However, when ble_bas_enable, the duf service disappears...
Hi,
Is is possible to use printf while using the libuarte library? I am trying to link the nrf_libuarte_async_tx() function to printf but I am unable to make it work....
Hi there,
I'm using nrf52840 DK and Custom board, SDK 17.0.2, Segger Embedded Studio(SES v5.20
my issue is when we send/TX data through UART "static uint8_t text[] = ...
Is it a good/bad idea to put capacitance on the nRST line. I noticed the nrf52840 DK does not have any capacitance on the nRST line. At least none that I can find, tracing...
Hello,
I have a nRF52833 on a nRF52833-DK or the PCA10100 and want to do development but I have found several projects don't have a Segger Embedded Studio project (for the...
Hello,
I just installed nrfutil with
pip3 install nrfutil
All the requirements are met:
andreas@notebook-fh:~/github/pc-nrfutil$ pip3 install nrfutil Requirement already...
Hi,
I need close to 1Msps rates for my application and am planning on using a ADS7887 SPI ADC from TI. My question is on how to drive the SPIM and if an example exists...
I am having trouble getting peer manager bonding to work, wonder if you can help.
I'm using nRF52840 (on PAN1780 eval boards), SDK 17.0.2, Nordic SES 5.30a
First a summary...
Hi
As there are 12 PDP context available on nrf9160, I was wondering about the correct usage of them.
Usually, my use case involves only 1 context (cid=0). I configure...
I am trying to measure the current using power profiler 2. The profile seems to contain irregular spikes which is incorrect.
Is there any way to make adjustments to the...
I'm using the peripheral_uart example and I'm trying to increase the buffer size.
At this point the buffer size is 20 although I changed in my prj.conf the following:
...
Hello
Just purchased and received the DKs of 52833 and 5340 to learn and develop several BT applications we have in mind. We are basically hardware guys, not software, but...
Hello guys,
After testing pwm examples, I would like to do my own program. But I have faced to different problems.
Do you know how can i configure PWMs channels. As I...
