After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
The chip we use is nrf52832 and the SDK is nrf5_ SDK_ 15.3.0_ 59ac345, the booeloader uses the example project nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040_ble_debug...
Hello,
I am developing one Zigbee based product for that I am using nRF52840 and light_bulb examples and modified as per my requirement.
Till now everything successfully...
I've just found through some trial and error that SoftDevice (s130 at least) on the nRF51 DK handles a sequence of notifications in the following manner:
call sd_ble_gatts_hvx...
Is it possible to （central side） send scan request fill the content based on received advertise information？
We want to control scan request message based on advertise content...
I am an experienced developer but struggling to understand nRF9160. Where can I find .h files defining HW? Where can I find data sheets describing peripherals? My task is...
Dear friend
Based on sdk17.0.2, in the ble_app_hrs routine, set NRF_SDH_BLE_SERVICE_CHANGED to 1, and by observing with nrf connect app, you can see that the Android phone...
If you take a 1K variable to a local variable, the AP will drop.
Static variables do not fall off.
I think it's a stack size issue, but how do I specify the stack size...
I am trying to get an nRF52811 to do extended advertising.
I am using: nRF5_SDK_17.0.2, version 7.2.0 of s140, SEGGER Embedded Studio 4.52, Windows 10
I have stripped...
I would like to confirm the update process when using nRF5SDK160098a08e2. I am aware of the following update process ----- Startup process: -MBR checks NRF_UICR->BOOTLOADERADDR...
Hello there,
I know how to measure the current based on Nordic tutorial. However, if I connected an external accelerometer by connecting Vdd and Gnd from nordic ev kit to...
Hi,
I want to run a CoAP server with Zephyr on a Thingy:91 over NB-IoT. Now I noticed that the Thingy only gets a private IPv4 address (10.x.x.x) from my provider which...
Hi, I am working on my custom made board, and I use P09 and P10 as digital outputs. I am aware I should disable NFC by adding the preprocessor: "CONFIG_NFCT_PINS_AS_GPIOS...
Hi All:
As the topic...........
1.what is the relations between the HID descriptor and data IN/OUT buffer?
2.Is the USB generic HID receiver_Function and tansmit_Function...
When launching the nRF9160, the following error occurred: <inf> at_host: UART check failed: 12. Dropping buffer and retrying.
Under what conditions does this come out? ...
