Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi,
I have developed an application on an nrf51dk, with SDK12.3 (as it was the latest that I could make it work with). It is running fine on the DK, but when moving to the...
Hello.
I am running ble_app_uart altered to allow for connection of two central devices.
The connection of two devices work fine.
Upon each connected central, I can...
Hello! I would like to use a predefined example from the nRF SDK and instead of the board's button, to use an external stimulus (let's say, an external button ). Similarly...
Hey,
I am working on the nRF51 DK and nRF51822 with SDK12,S130, trying to pass a SIG PTS test for required IOPT, however always getting the same "INCONC" verdict, the PTS...
Hi,
I am trying to interface IS25LP064A External Flash with nRF52832 using SPI. I want to get the device ID/ Manufacturer ID of the flash. I am able to get the same in Arduino...
Hi everyone,
I'm using the nRF5SDK160098a08e2 and i tried to compile the ble_app_eddystone exampe but i'm getting this compilation error!
cannot find ../../../../.....
I am unable to read any uart input when I configure UART1 with nRF9160DK.
Please let me know if anything is wrong in my code/config
main.c
nrf9160dk_nrf9160ns.overlay...
In the Sleep mode and nrf52810 was Broadcasting with space 125ms once.
The normal temperature was good,that only 0.08mA. but why not 85℃，The current was up to 0.21 mA ,it...
Hello
I would like to detect timeout when I send a confirmable coap message not received.
My problem is that the response I receive in my response_handler is always...
Hello.
I'm going to make a prototype board and use it soon. I will make a prototype board with nrf52840 and use it soon.
It's my first time developing a prototype board...
nRF sniffer: v3.0.0
Wireshark: v3.2.6
Hardware: nRF52840 ( PCS10056 )
wireshark did not show packets with MTU greater than 20 bytes, is it still not supported?
Hello ,
We are using the following.
Module: Bm833 (nRF52833) from Fanstel
Softdevice: S140 7.0.0
SDK: nRF5SDK17009d13099
Sample code: ble_app_uart
We have added...
Hi, We are developing a BLE app on nRF52840. For the next step, we want to try reading/writing to other devices through connector interface on nrf9160 dk. Is it possible to...
I followed the steps below: flash softdevice flash bootloader
generate package
flash package
But after that I can't connect to this board by using usb and need again...
Dear Team,
I am totally new to NRF24LE1. I have bought 6 pieces it through online. Iwant to program it using HAL libraries. I've searched it everywhere I ca do. But I...
