After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi Team,
I recently purchased 2 Audio DK's and I set one up as a gateway and the second as a left headset. I was able to pair the two, stream audio from my PC through the...
Hi,
We are currently developing a BLE device (HW and SW) using the NRF52811.
As we want to be able to update the device via FOTA we need to have the Bootloader to have...
Hello,
I am trying to upgrade my project from ncs 2.1.0 to ncs 2.6.1. I am running into some strange issues with mbedtls and I suspect it's because the same ciphers enabled...
Hi All,
We're going through BQB certificate with our mice, and we're informed that test get failed because new rule will be implemented in May 2023.
Our Chip is NRF52833...
Hello,
I want to use external flash. I did some research on the subject. I am using SDK 2.6.1. I have a few questions.
1- Does the spi_flash example I examined work on...
I have a custom nRF9160 board running a modified asset_tracker program. I am using UART0 as a command line interface for testing and debugging. I can enter commands to setup...
Hello. I'm trying to do spi communication on a custom board with nrf5340 used. I'm using three threads, I build it, but if I put it on the board, the board will have a problem...
Hello I’m using the NINA-B306-00B BLE module which uses the nRF52840 MCU for a custom board application. The BLE module interacts with two sensors, an accelerometer via SPI...
Hello, I get a compiler warning when I try to log a float value using the LOG_INF macro in my project. The code I'm using is from the cell-fund course: lesson 6, ex. 1. Toolchain...
HI,
I have a function testfun from a customer-provided .a library, and I hope to run this testfun function in RAM. I am currently using NCS 2.8 based on the nRF52840. I...
Hi, I read others cases obout the problem to send more than 20 bytes trhough BLE and add on my prj.conf the next three lines:
This is the entire prj.conf:
Butr when...
NCS 2.7.0
NRF52840 DK
I am trying to trigger an advertising sent callback to indicate advertising timeout or a maximum number of events. I have tried increasing the workqueue...
Im using nrf5340 with nrf connect SDK 2.6.
Im trying to follow this post to evaluate hardware timer for reading saadc
But I constantly am getting
CONFIG_NRFX_TIMER1...
Hi,
I have successfully built and ran the MQTT sample ( /opt/nordic/ncs/v2.7.0/nrf/samples/net/mqtt) on the nRF9160-DK. I did have a few problems with SIM coverage and firmware...
Hi,
running the latest nrfconnect vscode extension (v2024.9.31) the "Add configuration wizard" comes up and stay blank. Additionally, the Actions view is also empty, while...
