Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hello, I'm using an nRF7002 with an nRF5340 host processor to detect and process WiFi beacon packets in monitor mode. I've encountered an issue where the nRF7002 appears to...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
I am designing a battery-powered mobile device.
Previously, I was using Reg0 in DCDC mode, but I added an external 2.0V DCDC with higher efficiency (low Iq) and decided...
Hi!
I would like to know if anyone has any idea when we will hear more about the future products compatible with the new Bluetooth Core 6.2 specifications, as this will...
Backround: We are planning to use TF-M with a two-stage bootloader (NSIB & MCUBoot) using dual-slots for secure and non-secure images. We need to support configurable fixed...
To use ECDHE_RSA you need to enable the following Kconfig symbol:
This symbol depends on MBEDTLS_HAS_RSA_CIPHERSUITE_REQUIREMENTS :
This symbol depends on MBEDTLS_RSA_C...
I am developing a project for the Thingy91:X making use of the Asset Tracker Template.
Following the Getting Started guide, I successfully build for the Thingy91:X.
However...
Hi,
We have an existing nRF91 (nRF9151) project (NCS 2.9.0 ) that already includes multiple modules such as ECG, external flash, RTC, modem, etc. Now we want to integrate...
Hi Team,
I would like to interface the nrf9160 with nrf7001 by using the SPI. While building the WIFI-Scan example by using SDK 3.1.1. Even by using WIFI-shell example these...
Hi team,
I am experiencing a persistent MPSL assertion 1519 on nRF54L15 that occurs consistently at ~5 seconds after BLE advertising starts. The assertion indicates that...
Hi everyone,
I’m using nRF9151 with nRF Connect SDK 2.9.0. Without changing anything in overlay, prj.conf, or source code, several of my projects suddenly started failing...
Hi Nordic DevZone,
We recently acquired some Pro Micro nRF52840 Dev Boards ( link ) and were looking to use them with the nRF Connect SDK. The boards use a UF2 bootloader...
I have a question about the nRF54L15.
１．I would like to know the maximum number of devices that can be registered for whitelist and bonding.
２．I want to know how to...
I am having an issue where my nRF52840 Development Kit is not being detected by nRF Connect for Desktop , specifically in the Quick Start and Programmer apps. The DK does...
Hi, I have an Adafruit Feather nRF52840 which I'm programming using SDK 3.1.1. I want the following UART config but it is being rejected with error -134 which I believe means...
