Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
NCS2.0.2, nRF5340 audio DK, VScode
about Le Audio
1.CIS mode,when is bidirectional communication supported?
2.when LC3 support 16bit 16kHZ?
3.when suppourt DFU...
Hi i wonder how could i program the nRF Dongle with the sample thread_cli in order to being able to use the thread topology monitor?
I know that i have to use the Programmer...
I connected my NRF52840 DK board via USB to my Macbook Air. In VS Code, under "Connected Devices" I was expecting it to show up as "NRF52[...]" but it is showing up as "NRF51xxx_xxAA_REV1...
Hi,
follow the to do DFU over UART on nRF5340, it fail in the last step "image confirm".
The console show
What is the meaning "Error: 3"? How to fix it?
Can I...
We have relatively big model composition, and reading it via nRF Mesh app fails if it exceeds 21 segment message.
However the limit I assume should be at 32 segments and...
Hi,
We have done a lot of projects with nrf52832 with softdevice S332 v5 before.
Now we have a new project to use nrf52840. Can we use the original s332 version? Or do...
I and looking at using an nRF52 device with the nRF Connect SDK version 2.x with a Zephyr Bluetooth LE Controller in a peripheral application where the advertisement data...
Hello,
I am running windows 10 and started the DevAcademy lesson 1, exercise 1 and exercise 2.
Up to exercise 2 item 4 (add a build configuration) everything went fine...
Hello i am using an nrf52840 s140 and i am trying to write a specific event when takes place to the usb port. I am using the usbd_uart example.
It works fine for the first...
I used Nrf9160 to develop a product. Until yesterday, I had been able to connect to the nb network normally. But today, I found that my device could no longer register to...
Hi, I'm looking for help installing the nRF Connect for Desktop 3.12.0.
I've managed to unpack the application EXE and have picked out all the required pre-reqs to do the...
Hi,
I have a problem, When I first initialize Bluetooth and then initialize FDS for writing, it will fail. However, if I first initialize FDS and write data ,it is OK, then...
Hi,
We develop a custom gateway in which we use iMx6ULL and NRF52840. Both are connected over full UART.
We use this NRF52840 as a BLE HCI controller by flashing the HCI_UART...
