Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
The datasheet for the nrf52832 specifies two key constraints:
I/O pin voltage max VDD + 0.3V, min -0.3V
The AIN0-AIN7 inputs cannot exceed VDD, or be lower than VSS...
We use the pc-ble-driver with the nRF52840-Dongle and we experience intermittent issues where communication with the dongle will just stop and result in a NRF_ERROR_SD_RPC_NO_RESPONSE...
Hello,
I am having an issue with trying to install the nrfutil program from this Nordic download page . When I click on the download for the Linux(x64) version of the nrfutil...
I'm not totally clear from the SDK documentation on when I can expect NRF_ERROR_BUSY from sd_ble_gap_data_length_update(). Would it happen in the case where both sides attempted...
Hello,
My peripheral device is nRF52840, central is an Android device, Sniffer hardware is PCA10040 kit.
Using this guide https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_BLE_UG_v3...
We have an application that needs to read device battery voltage and a sensor value every 10 seconds. The ADC is using burst mode and 8X oversampling to take each sample....
I created a new dts folder for nrf5340 appcore. The application works fine on the project, but I find netcore is not working properly. I found that the BOARD_ENABLE_CPUNET...
Hello,
My device is already implementing DFU over BLE and all is working fine. But now, I want to add the update over LTEM (Quectel BG77).
I want to proceed like this...
Basic OpenThread application built for 5340 crashes in net app.
The same application works fine on 21540 (52840 + 21540)
The crash seems to happen when some thread packet...
Hello,
I have 2x PCA10040 dev kits connected via SPI.
Device #1 is talking to a custom board MCU by UART
Device #2 is connected by BT to my android app
The task is...
Hello,
I am planning to use the balun BD2425P50100AHF with the nRF52833. The voltage on the pins BAL1 and BAL2 can go up to 15V.
I am wondering what is the maximum allowed...
Hi,
We have developed an application in central mode using BLE nRF52833 chip running on SoftDevice140 , Version 7.2.0
We now need to add support for FEM nRF21540 ...
Hi,
I am using NRF52840 development kit and I need to modify the PCNF0 register values for our application.
I am developing our application using the sample application...
I have ran the Mesh light demo successfully, and capture the Bluetooth HCI log (*cfa file) from my Android phone.
However，the transaction between my phone and the nRF52840...
Hi everyone,
Not very sure this is the right place to share this, if not, moderator please help me to move it to where it should be.
I just want to share with you a...
