Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi !
in https://infocenter.nordicsemi.com/pdf/nRF52840_PS_v1.7.pdf specified operation frequencies
"
The IEEE 802.15.4 standard defines 16 channels [11 - 26] of 5 MHz...
Hi, I am working nrf52832.
this is a example for sdk nordic and i want to know why when i include a byte (value 0x00) in the m_beacon_info, this data is not reflect on nordic...
Hi, In the documentation I read at uart_rx_enable a timeout setting in Microseconds . Under uart_rx_enable_u16 the timeout is defined in Millisecond .
Do those really differ...
Hello,
I'm new to Nordic Zigbee solutions and where to find information so hoping someone can point me in right direction.
Using 2 nrf52840-DK boards. One is flashed with...
Hi,
We are trying to move from segger studio build environment to GCC/Make starting from the Example Makefile and adding source files and includes. The project consists...
Hi,
I am currently working on a project using a nrf9160 board (sdk 1.7.1 and Modem FW 1.3.1) and I am using PSM.
During my test, I put the board in a metal box to simulate...
Hello,
I am using nRF52840 DK to build ble_app_interactive.
Now I have device with NUS,I can connect to device using ble_app_interactive.
I have added NUS into...
Hi,
I am successfully connected to central and peripheral, Now i want to push-button(nRF52810, custom board) and this information should be received by central(nRF52832...
Hi,
nRF5340 Audio Application working very well while im using 2 nRF5340 board.
But i wonder, how can i connect to the other brand's board using nRF5340 Audio DK ?
I...
Hi,
we got a nrf5340 audio DK recently, when want to build example code for it, I get this message：
warning: attempt to assign the value 'y' to the undefined symbol HW_CODEC_CIRRUS_LOGIC...
Hello!!
I have explored extended advertising using both nRF5 SDK and nRF Connect SDK. Using nRF5 SDK, it is not possible to advertise 1650 bytes in an extended advertising...
Hello,
SDK17.2, keil5,nRF21540-DK
my project use i2c and spi, but got error:
Error: L6200E: Symbol SPIM0_SPIS0_TWIM0_TWIS0_SPI0_TWI0_IRQHandler multiply defined (by...
Hello,
SDK17.2, Keil5, nRF21540-DK,
when change DCCH to 3.3V as above codes in main first,
(1). the uart will can not work ,
(2). change pin to high voltage as follow...
