i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
hi,
I have a problem about NCS1.9.1 NVS.
I performed `nvs_write` when ble is connected and then a reset occurs:
Whether NVS write can be performed when bluetooth is...
Hello All,
I'm new to using Nordic development kit and VSCode but I am running into an issue when I am trying to build a sample application. When I use the template to create...
I am using bt_nus_send to send data via BLE every 1ms. I've noticed that when connection is bad, this function takes a couple of milliseconds to execute, while when connection...
Hello,
I'm currently developing on the NRF9160, a sensor implementation that sends a few 100 bytes every 24hrs.
However, for demo purposes we need to send the payload...
Hi,
I am working NRF DK (NRF52840), when I am trying to flash the program in NRFGOSTUDIO from that it was showing some error that is " No device detected, or readback protection...
Hi, All
I am using VS Code and nRF connect v1.9.1, I try to set some parameters for scan etc. during running. It would be ideal if they can be saved into NVM and loaded...
Hi,
I am conducting a mesh test and it contains:
An android smartphone,
- running nrf mesh 3.1.7 on github
- sending hundreds of bytes packets to the mesh nodes...
Hi,
I am completely new with the development kit nRF5340, I have plugged in the USB and turn it ON, the status after that as follows,
- LED5 is blinking continuesly
...
Hi I have been doing some current consumption measurements using Nordic's Power Profile Kit 2.
The device I am measuring is a custom BLE device that uses the ADC to sample...
Hello, I'm having problems to debug my application when I check the "Enable debug options" in the build configuration. If I don't check this box, I can debug, however, most...
Hello,
I'm working with a little project in NCS 1.9.1, chip is NRF52805 acting as central, connecting to a peripheral that requires passkey and L3 security. Everything works...
Hello,
We are developping based on SDK 15.2 for nRF52 using IAR 8.11 and S132 V6.1.0 as softdevice for central/peripheral application. Bellow is the test scenario explained...
Hello,
I have an application where I send the data I receive over UART, directly to a phone connected with BLE. However, the BLE connection is often not fast enough to send...
I am using nRF52840, SDK16.0.0, Keil v5.18a to developing application. When I changed heap size in Keil C/C++ option, it failed! It can be successful if you change heap size...
