Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
I built the project on VS CODE, but it failed at the beginning
log output:
> Executing task: nRF Connect: Generate config nrf52840dk_nrf52840 for f:\nordic-sdk\project...
Hi, I've made custom boards using nrf52840. In my application I did advertise forever with interval of 200ms. Now after several weeks of tests I've two boards out of seven...
Goodday
I thought I would try the webinar
️ nRF Connect for VS Code Webinar - Hackster.io
Im getting the following error after I add Build configuration
Building...
After installing NCS 1.9.0 Open Segger Embedded Studio does not show as an option any longer. I have tried to remove the SDK and install it again, but the result is the same...
Can distance be set between nRF52840 and APP? For example, set 5m and 10m through app. When the distance between nRF52840 and APP exceeds the set distance, app will remind...
Hello Respected members, I have a question regarding the #nrf5-calendar example that is, is there any way to retain the NRF52 time after resetting the device. I am using the...
Hi there!
I'm currently looking into performing a DFU on a nRF52832 DK from an SD-Card. I managed to get the secure serial uart bootloader up-and-running and have no issues...
Hallo,
I would love to receive some support in configuring micro_ecc backend for OTA DFU.
I am using SES and following the instructions on nordic InfoCenter. The link...
Hi,
I am using nrf5280 development kit and 17.1.0 sdk.
i am working on ble_app_uart example code.
Its working fine no issue. Since the start address of the application...
We are using an nRF51x22 in one of our designs.
I am in the process of writing a bootloader that conforms to a packet format we use for loading code across our product line...
hi support team,
Customer IAC is now on GPS testing sensitivity performance. Below is from 9160 spec.
now they are trapped here for a long time. do we have any instructions...
After preforming a DFU with the nrf connect app (ios) the device advertises and will "connect" with the nrf connect app, but its not actually connected which is evidence by...
Hi, I have a project that is comunication between nRF and Smartphone via BLE and using libuartes to comunicate with 2 another devices via 2Uarts. Now I need to combine 2 examples...
I have an BLE peripheral application running on a nrf52833 with softdevice S140 were I transmit data from Bluetooth to an external CAN-controller via SPIM and back. This is...
Hi, I want to enter the DFU by setting the register.But when the sd_power_gpregret_clr and sd_power_gpregret_set are set to set the register, and the err_code is 0x02 is returned...
