Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
LE audio demo,i enable CONFIG_STREAM_BIDIRECTIONAL ,when i connected Galaxy Buds3 by cis.
my uart_tx will stop.cpu looks busy.when disconnect with headset.data will...
Hello, I have a problem trying to connect Direct Test Mode desktop app to my custom board running Zephyr on nRF52833. My firmware sample is based on hci_uart https://github...
Hi folks,
I've been trying to use the sw_pwm to generate two PWM outputs. I'm using sw_pwm because I want to achieve lower frequencies (1-100Hz) and the hardware PWM API...
Hello,
I need to connect the Thingy:91 to an MCU via UART and/or SPI bus. I need help to identify the pins for communications for:
SPI: CSK, CS, MISO, and MOSI
UART...
Hi, I am new to working on the display . I am trying to integrate nrf5340dk board with waveshare lcd module which is of 1.14 inch and has st7789v controller by using SPI communication...
Hi,
Legacy SDK bootloader and dfu preparation workflow had the following option:
hw_option allowed for checks, whether supplied firmware matches given hardware. So firmware...
Using nrf5340 audio DK & ncs v2.60
I modify this function to print this information when the number of packages reaches 100.
\
Part of the result:
120*100*8/(...
Hi, I'm trying to implement timer synchronization on one central and multiple peripherals, I'm using nRF52840 and NCS v2.8.0. I've seen the example conn_time_sync which uses...
Hi,
I am using download client for downloading a file.
I am using download_client_get and get fragments in callback.
When the file requested is short in the callback...
Hello Nordic Team,
I'm developing a project with two nRF52/nRF54 microcontrollers where I need: - 1st microcontroller as BLE peripheral receiving mobile app data (nRF connect...
I'm migrating code from ncs 2.7 to 2.9.
I am using CONFIG_BT_EXT_ADV and scan timeout callback - such timeout requires CONFIG_BT_EXT_ADV:
It was working fine. Now it's...
Hi,
I follow the custom board exercise steps with mynRF52840 DK and when I reach step 8.1 , in the deviceTree visual editor, I notice that the GPIO0/1/TE options under ...
Hi, I recently updated from NCS 2.6.0 to NCS 2.9.0 which had lots of changes. I believe I ported from child_image to sysbuild with success, as my main application on app core...
Nordic has changed the API of nrfx nrf_modem_dect_phy from SDK 2.7 to SDK v2.9.
In struct nrf_modem_dect_phy_callbacks there is an additional callback member stf_cover_seq_control...
