After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Segger cannot seem to find the user included directories. Every time I compile any file I get this error or something similar of {name of file} not found as shown in the pic...
hey
I have worked on BLE, and learned the BLE protocol stack. Now i am learning BLE Mesh. I found the Mesh is also having a stack, I could not understand why both the stacks...
Hallo,
I request for your time and effort to solve the issue that I am facing at the moment. Any suggestions and solutions are highly appreciated.
Hardware: NRF52840DK...
Hello,
It there a download for the nRF-Command-Line-Tools_10_12_2_Installer_64.exe?
I only see a zip file with this and a python setup. I have an internal program...
Hey, I've a string of less than 10 bytes (10 characters max) and I'm establishing the connection between the Central (nRF52833-DK) and the Peripheral (nRF52810) and I've set...
Hello,
We are trying to use the Cryptocell as used in example nrf_crypto_aes_cbc_with_padding along with Secure DFU. However, when the application loads the crypto engine...
DFU secure bootloader ( secure_bootloader/ pca10040_s132_ble ) using segger embedded studio version 5.50
Am using SDK version 17.0.2 for BMD350 nRF52832 module
Already...
Hi there,
I was able to successfully compile and run the "BLE HIDS keyboard" example on my nRF52832 using Segger SES 5.44
My Nordic chip is connected via UART Rx/Tx to...
Good day
I use NRF52840 + SDK v17.0.2. My application relies on _gls example and mainly copies its security settings ( also uses peer manager ) except I use MITM protection...
Hello Dear!
Please look at the red area in the picture.
The C9 820PF, it's no commonly used,We buy it very hard.
Can i modify C9 820PF to change C9 1 nf in desgin?
I've read quite a few threads where people are asking for help getting NAND Flash to work with their devices, only to find out they are not supported. I see that only NOR...
Hi
I am using nrf52832 to develop a ble hid device with tile function
I merge sample code ble_app_tile to ble_app_hid_keyboard example
I use the advertising_init function...
The firmware crashes when passing the ble_stack_init() when the firmware is download but in debug mode it works fine. The screen shots below shows this event.
We are using...
Hi there,
For my POC test, I need to send a max 255 bytes payload data from a client to one or many servers. I use two nrf52832 DK boards, BLE sdk 17.0 and BLE mesh 5.0...
