But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Is it acceptable to use the nrf52805's DEC4 pin as 1.3 V reference? I've connected the pin across a ~11 MOhm divider to to create a 0.12V reference for an op amp. I figured...
On SDK16.0.0 + Mesh SDK 4.1.0
I am using a Fanstel BT840X module that has an onboard Skyworks SKY66112 PA/LNA.
I followed the Infocenter guide along with an old example...
Hi, I'm having an apparent memory issue after increasing my PPI channel and GPIOTE allocation. Here's the basic setup:
nRF52840 with SoftDevice 6.1.0
SDK 15.3
I...
Hello,
We're intending to use the free flash region for two purposes: Flash Data Storage and DFU. The Flash Data Storage will be allocated a large number of pages (100...
I am using the example on sdk12.3/examples/ble_peripheral/experimental_ble_app_buttonless_dfu and copied the relevant parts to my app.
It is now apparently working. The...
Hello ,
currently i am working on indoor navigation project for that i was setup 4 node in a square shape, the nrf52832 beacon was continue transmitted packets. we also...
Hello,
I've been looking into the performance of the coded PHY (S8) to see if it fits the needs for a product we intend to make. All research and documentation I found about...
Hi,
Im currently wondering how I would power the nRF52 dongle with a 3.85 Liion battery the best way. Voltage range will be between 2.5v and 4.2v.
I read you can use VDDH...
Hi, I am trying to make the iBeacon emulator using nRF52840-DK without SDK. I have found the iBeacon packet format.
When I send this packet using SDK, that worked. Now...
Hi all,
I am having a problem with the startup of the software on an nRF52840. It works fine on an EVM but not on our own board. The software is hanging in the softdevice...
Hello,
I have loaded the https_client sample to my nRF9160 DK, and when it runs, it blocks after printing "Provisioning certificate" for 10 minutes exactly. That would mean...
When installing the Nordic Connect for Desktop environment on macOS, a requirement is a running Apple Xcode IDE. The scripts which invoke Xcode (whether doing a manual install...
My project has successfully debugged the communication of SPI_2, SPI_3 and UART_1. Now I need to debug the interface communication of I2C, when I turn on the macro switch...
Hi,
I need a way to have a concurrent connection (multi-peripheral), with whitelisting and bonding. Is there any example of this?
I found an example for multi-peripherals...
