Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi, We were trying with a new n/w carrier in Canada ( Maxim ). nrf9160 is able to connect to the network, but it is not able to resolve our server URL ipv4 address. Below...
Hi,
I am testing RX mode.
And the module is sure to enable M1 (%XSYSTEMMODE: 1,0,0,0)
I use the following command, but return error.
AT%XRFTEST=1,1,2,19500,17,1,0...
Hello,
I´m writing my thesis and using the Online Power Profiler to get a estimation about current consumption in NB-IoT cases.
I would like to use the diagram from the...
Hi, I have developed zigbee stack.
I tested to connect the door lock example of Thread and Zigbee SDK 3.2.0 with ZC of SDK 4.2.0.
I checked connection with these.
So...
Hi,
We are going to use NRF52832 for a project, and planning to design our own PCB card and assemble the NRF52832 chips, purchased through Digikey or a similar distributor...
Hi everyone,
I have designed a project based on the Radio test example, in the Nordic SDK. After programming all my code on the NRF52833 DK (PCA10100), i decided to design...
Hello, I have 4 NRF51822 modules, 2 stlink programmers, and a BLE400 board, I was using the same module with the same stlink each time, but the led on the board stopped lighting...
Hi,
I am going to transmit and receive data with libuarte. I read the libuarte example, but I am not quite sure my understanding of the data transfer process is correct...
Hello
I am trying to configure the spis with the nrfx drivers. My code is as follows:
I enabled the nrfx SPIS driver and the nrfx SPIS3 instance via Segger Embedded...
Dear,
I want copy antenna design from PCA10040 for BLE. Could you please help to provide antenna's spec, such as gain, efficiency, Radiation Pattern?
Thank you.
We are trying to program the nRF5340 via SWD from a host MCU and would like to understand if there is a white paper/blog post similar to this one:
https://devzone.nordicsemi...
Hi, Currently, we work on a project that uses: nRF9160 Zyphre OS Segger Embedded Studio for Arm (Nordic Edition) V5.10d SDK v1.4
This is our situation.
We want to measure...
A few things to preface:
Hardware: nRF52840 Development Kit (PCA10056 - 2.0.1 - 2020.11)
Nordic SDK: nRF5_SDK_17.0.0_9d13099
Central example project I am using: nRF5_SDK_17...
Hi,
How do we get the GPS speed accuracy out of the module? We have used other GPS modules in the past which have output the speed accuracy which we use to qualify the data...
