I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
Hi Sir,
I have a question about these two configurations in overlay-ppp-cmux-linux.conf, CONFIG_MODEM_BACKEND_UART_ASYNC_RECEIVE_IDLE_TIMEOUT_MS and CONFIG_MODEM_BACKEND_UART_SLM_TRANSMIT_TIMEOUT_MS...
Hi,
I recently started working with the nRF9151 DK and was able to run the initial demo programs without any issues. To continue testing, I picked up a Thingy:91 X, but...
Good day, Nordic staff!
We are working on a product using the FLPR for its intended peripheral-controlling purpose. For us, the best way to send commands to and receive...
Greetings to everybody! There is some question about nRF54L15-DK board measured current consumption. I measure current via the P6 connector, that is, I measure current within...
Hi，
The same hardware and software have been in continuous production for several years without issues. However, the latest batch exhibited abnormally high power consumption...
Hi,
I am developing a small app for the nRF52840 using the SDK V3.1.0 and the Visual studio Code on a PC windows 11.
What I like to do is to be able with the app to change...
Hello,
I'm using the nRF5340 and have configured UART with EasyDMA to receive a variable number of bytes at 307200 baud. Our application has strict timing constraints, so...
To preface:
Board: nRF52840DK
OS: Windows 11
nRF Connect SDK / Toolchain: 2.9.0
VS Code Extensions:
nRF Connect for VS Code: v2025.5.152
nRF Connect for VS...
Hi guys,
I am currently working on a data migration of the settings storage to the external flash.
The problem I am facing is that after an OTA update, the device does...
A project I am working is proposed to have an nrf 5340 connected via UART to Yocto (Thud). Am looking for suggestions on an embedded client that will work with v3.0.0 of the...
We are using this custom baord to check the I2C addresses where the I2C BQ_SCL (P1.00) and BQ_SDA (P1.01) connects to various peripherals. However we are unable to get the...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hi,
I am trying to install nRFconnect SDK and VS Code Windows 10 by following NORDIC Dev Academy lessons.
Encountering following errors while building the following example...
