When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi Dev team,
I am working with a nRF9160DK board. I am currently getting an error while building my SPM folder in : C:\Users\adeel\ncs\v1.3.0\nrf\samples\nrf9160\spm.
...
Hello!
I'am from austria and try to connect a Thingy:91 to your nrf-Cloud. First I tried it with your
iBASIS sim-card, but in austria we can't use this card.
Then I...
Hi all.
I did a layout with NFC antenna with a nRF52832 chip.
In the schematic (suggesten on datasheet) I have antenna coil with 2 capacitors to ground.
Drawing...
Hello everyone.
I would like to set-up a mesh network of Thingy:52 devices and an nRF52840, which would help me communicate from the an external stimulus to the phone, via...
I have an application where the nrf52840 dongle is hooked to a sensor. The sensor drives a pin high, the mcu grabs data from the FIFO (SPI) and puts it in a buffer. So far...
Hi Team,
We need to use Flash as EEPROM and we have the following queries,
1. How much maximum size of Flash can be configured/emulated as EEPROM/NVM?
2. Whether below...
When using the serial_lte_modem application on a custom nrf9160 board I have discovered that I get nothing out of the UART unless I pull VEN low and then release it (reset...
Hi guys,
I am using Zephyr RTOS and trying to enable my device to send the voltage data via BLE. I use two nRF52832 boards, one of them is peripheral for which I use peripheral_ht...
Hi Team,
We need to know the what kind of security level available in Nordic nRF52X(nRF52833).
Secure boot support and where the 128bit AES keys are stored and accessed...
Hi Team,
We are going to use nRF52833 chip-set and we need the below information based on this input we will decide our chip-set.Kindly update your support.
1. What is...
Hi ,
The size of the boot loader partition 24KB is fixed for the lifetime of the device or it can be extended, as we have some feature to add like firmware update.
Firmware...
Hello,
I read through the datasheet of the nRF85832 to understand the peripherals a little bit better, but I got stuck while looking through the register overview (in this...
I am using NCS-Zephyr, Zephyr version 2.3.0-rc1. If you need to know the NCS version too, please can you include how I can find this?
When I do west flash normally (which...
Hi Team,
We have requirement for firmware update over Ethernet [ external Ethernet ENC28J60 module interfaced over SPI] 1. Is bootloader customizable for adding SPI driver...
