Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
We want to understand any surprises with using nPM1100 on existing or future products.
I just bought two nPM1100-EK units and finished the first round of my evaluation....
We could have found "transmission delay" in 2ch Audio recording sequence.
Here are the detail about the environment of DUT, and phenomenon.
Please find the attached file...
Hello!
When turning on the board, USB connected to the Mac, a software drive named JLINK keeps mounting and being dismounted, as on the video of this link: JLINK video Only...
Hi there,
How can I copy and customize an existing Zephyr driver?
I'm looking to extend the implementation of the LIS2DH driver in Zephyr.
The driver does not support...
Two simple questions:
1) I'm using the Zephyr OS on the nRF52832. What is the easiest API for storing a small amount of data in FLASH memory?
2) Is there an index of the...
Hi everyone,
I am getting started with the nRF52832 and am testing it with the nRF52DK. I just completed the nRF Connect SDK Fundamentals course and now wanted to test the...
I'm updating our nRF5340 firmware from SDK 2.4.2 to the SDK2.9.0. After few modifications, I was able to compile it using the SDK2.8.0. Now I'm trying to compile it with SDK...
Not too long ago I was able to use Segger Embedded Studio with my nrf52840 DK, compile and build projects and run it. Unfortunately I have moved to a new computer and trying...
Hi Team,
I am trying to commission the matter over thread light app on nrf5340dk with my OTBR using chip-tool but getting below error every time.
OTBR is running on...
I am investigating use-cases around indoor positioning, particularly in commercial and industrial environments (warehouses, factories etc.). The customers prefer to not roll...
Hello,
We were developing on an nRF52840 board with the NCS 2.6.1 SDK and had configured logging and shell capabilities via UART. Once we moved to the 2.8.0 version, we...
We're trying to use the VERSION file, to both generate the app_version.h file (so that the application can know its own version numbers), and to update the version which gets...
Hi there, after installing toolchain and SDK (2.9.0) on Windows 11 (python 3.10) I've successfully build an example and generated the merged.hex but issue occurs when trying...
Hi, one of my nRF52840 dongles cannot be detect in device manager. When I plugged it into a USB port on my pc, the red light slowly blinks and it didn't appeared in ports...
Hello there,
I got an error msg when I tried to compile the Bluetooth LE UART service example for nRF54L15-DK as: " devicetree error: /chosen: undefined node label 'uart0...
