Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi,all,
in the Core 4.2, the sentence with word 'Controller' and 'Host' have appeared many times.
like 'When a Host performs the auto connection establishment procedure...
Hello,
I'm using a custom board (nRF51822 QFACA chip), with the optional 32KHz crystal.
When, I use the SDK 5.1.0 and the S120, my code works perfectly. But when I try...
I would like to develop some BLE applications using the nRF52 Preview DK, that embed a NRF52 revision AA. S132 soft device 2.0.0-8.alpha documentation says that is not compatible...
I've been developing some ble code for a custom board. Recently, I just finished creating a new smaller board. When I load my code onto it, I notice that I have trouble discovering...
Can the nRF52 be programmed by 6-pin J-Link Adapter by just connecting the following 4 pins,
Pin 1 : 3.3v Supply,
Pin 2 SWDIO,
Pin 4 SWDCLK,
Pin 5 GND,
Can pins 3...
I want to save custom data in NV address. Which address is safe to save custom data in NV?
I'm working on nRF51822-xxAC with very simple and small code.
And, using s110...
My project for nRFs has a few configurations for different boards.
So, how to enable 'batch build' button to build all configurations by one click? Currently this in disabled...
code.c
ui_flash.c
ui_flash.h
Hi guys,
So we are building the Ibeacon project , and faced with some problem:
The chips falls hard reset periodically when trying...
Hello,
Is there any todo list about how to protect an application from hacker unsollicited copies to avoid illegal clones ?
how to allow jtag in write only (disable...
Hi all,
For PAN 42 which describes an issue write to RAM after a POR. When was this issue fixed? I can't seem to find out what versions of Silicon are subject to this issue...
Hi, i try to understand how to use power down modes. But i have a problem in the example ( nRF24LE1 REGISTER RETENTION TIMER ON ).
while(1)
{
// Register retention mode...
Hi All,
I'm facing unstability in connecting my Central BLE device based on bluez to connect to Nordic Uart service based device.
For every 10th or 11th connection ...
When I use a power supply, (3.0Volts-60mA limitation) with the DevKit boards nRF51 or nRF52 the input voltage is clamped at around 2.0 V and the current is 60mA : the SoC...
Hello, kindly any one tell me how to run a beacon code in nordic Ev kit . I've been trying to make it work . What type of changes i need to do in the code .
Hi,
I want to migrate my firmware from nRF51422 and softdevice S310 to nRF52 and softdevice S332.
Please share migrating step if anyone knows.
For nRF52 and Stack S332...