This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
We are implementing a small battery powered BLE advertiser using the nRF51822 with an odd requirement that the advertising data needs to change between each advertisement...
Have configured battery service as the example ble_app_hrs.
This works well, but the BLE PTS fails.
The battery service has been configured for multiple instances.
...
I have a nRFready Smart Remote Kit.
nRFready Smart Remote feature:
Device : nRF24LE1
Host : nRF24LU1+
Can I use it in Android OS(for example Samsung Smart...
hii....
am working on a custom profile having broadcast feature in active connection... am advertising some sensor readings and scan response and a battery service before...
Keil uVision 5. SDK 7, SD310 Version 2, PCA10028 board
I'm NEW to ANT. I have running ble_ant_app_hrm example. The code compiles with no errors or warnings, loads, and...
Please help: Debug is mentioned in many places and is of several types (uart, ble, assert...). I need clarification to distinguish which debug type is in effect, and how to...
I have a project based on ble_app_lbs example. When I started the project I was using the S110 stack and SDK 6.1. I have much of my BLE code working, but the project has expanded...
It seems to be the case that pstorage_write errors (for example forgetting that it needs to be word-alignment, so 4 bytes at minimum), do not end up in the pstorage_callback_handler...
Hi there
I have never used a nRF51822 device but it looks like a good option for a product development.
Reliability of the link is a priority so the design will include...
I want to connect Bluetooth Smart chip to a weighting scale, read the data and send it to a phone.
Is this possible and what requirements there are for the scale?
The Manual of the nRF518-SDK version 5.1.0 mentions something called nrfprog. Unfortunately the SDK doesn't include it. Unlike what i found on google, i see no nrfprog in...
I have an nRF51822 design that programs fine from the embedded Segger on the eval board.
However, when I try to connect an actual J-Link Base, I can't seem to get it to...
Hi
I have PCA10005 module disassembled from mother board and with VCC_nrf, GND connected to external supply. The chip is able to work with pre-programmed data.
Is anyone...
Hi,
i have a generell question. First i have to say i am not the best programmer, but maybe some one with more experience then me could help me.
Does it make sense to...
Got nRF51422-EK.
Followed instructions and used nRF51 SDK v6.1.0
LED next to the Segger part blinks constantly.
If i build and download Blinky, the LED0/1 do not alternate...
