Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hello everyone,
I'm looking for some advice on a slightly offbeat topic related to the Nordic SDK.
I'd like to modify the Makefile of one of the SDK examples so that it...
Hi there!
I am trying to make an application that plays an audio sample to a BLE speaker (another nRF5340 running as headset) where the audio sample is in memory. I have...
Hello,
I am writing to inquire about an issue occurring on our custom board.
Ideally, we should print the logs from the device to identify the exact cause, but since that...
Hi everyone!
I have been developing an application for some time and everything has been running smoothly, until recently testing it and finding out some inaccuracies. ...
This library ( https://github.com/NordicSemiconductor/pc-ble-driver-js ) is pretty outdated, and the linked installation instructions are in an archived repository.
I...
I have a chip that I need to read from connected via SPIM. As one might expected, I have a FIFO I need to read from and a data ready interrupt to trigger the read. As an added...
Hi
I'm wondering if I can build a Bluetooth Mesh network for up to 3500 devices. I researched the BLE Mesh standard and theoretically the protocol can create a mesh with...
Hello,
I'm trying to test if my device BLE5 is working properly. I have an nrf52840 pcb and i using the ble_app_blink_pca example. When used the example as is with an BLE4...
Good day! I want to use Fat FS to connect to a micro SD Card on the Xiao BLE board. Is it possible to configure the board without the help of the expansion module? The main...
Hi
I'm trying to add to my Linux board (RPI4 CM) a cellular connectivity and I thought about using nRF9160 SiP because it's a product I've already used and it's low cost...
Hi
Spotify 128 kbps aac stream is about 16 bytes per ms. Ble should support 31 bytes per packet.
So can I stream 16 bytes ms over lte m to nrf 9160 then via uart to...
Good morning!
I hope you will forgive my trivial question but I am a beginner. I don't quite understand the partition structure presented in the "NVS" example. Using the...
Hi,
A veteran of nRF5 SDK but new to NCS.
I tried to run tx_rx_non_blocking example from the latest (2.6.1) NCS SDK, but can't get it to run (nR52840DK)
It seem...
Hello, I recently set up an nRF52840 with the nRF7002 evaluation kit using the WiFi station sample. However, during the build process, I noticed that it consumes a significant...
Hi,
I'm integrating an external SPI flash W25Q32 with the nRF52840 using the NOR FLASH driver, but it's not functioning properly as the MCU log indicates an MPU error. ...
