I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi
Followup on this ticket: Enabling SPI and TWI drivers on Zephyr
First the fundamentals, I am using:
nRF52840-DK
nRF Connect for VS Code: v2024.7.13
nRF...
Hi
First the fundamentals, I am using:
nRF52840-DK
nRF Connect for VS Code: v2024.7.13
I am trying to create a demonstration project, where I need both SPI and...
I am currently working on a project where I need to connect my nRF52833 microcontroller to other devices using the Nordic UART Service (NUS). I am using the nRF SDK and Segger...
Hello, I.m using SDK 2.6.1 with VSCode.
I created a new application based on the sample /nrf/samples/net/mqtt configured for nRF9161_ns which is listed as a compatible board...
Hello! I am a newcomer to nrf and embedded programming (other than basic arduino and micropython projects). So far I have gone through many of the devacademy walkthroughs...
I cannot get the nrf5340 audio dk kit to work from USB input properly. After a reset, it only works for a fraction of a second and audio stops. Has anyone run into a similar...
I have three nrf5340 board. Now i want to use one as bis-headset and two as bis-gateway. I want to get two audio from two bis-gateway at the same time. Can i do it? How ?...
I am using an IMU sensor in sensor hub mode (LSM6DSV16X, LIS2MDL) with the FIFO interrupt interval set at 30 Hz. The data is sent over BLE. It works perfectly when using RTT...
With nRF7002DK and TF-M (nrf7002dk_nrf5340_cpuapp_ns.conf) configuration, the sample project works for example.com:
*** Booting nRF Connect SDK v3.5.99-ncs1-1 *** HTTPS...
In my last question, devzone.nordicsemi.com/.../can-cis-and-bis-modes-work-at-the-same-time-or-switching-freely , I have asked that if the CIS and BIS modes can work at the...
During my test of the nrf5340 audio application which in the V2.6.0 SDK , Because of that i need to implement some algorithms in it, i use the ld file to allocated a segment...
I am having trouble understanding how to measure the power consumption of the nRF9161DK as recommended by the documentation: https://docs.nordicsemi.com/bundle/ug_nrf9161_dk...
Hi,
I'm struggling to use ble_app_att_mtu_throughput and spi. Some help?
When I merge the two codes the main code (ble_app_att_mtu_throughput) doesn't work.
Thanks...
Hello,
I am evaluating the nRF9161 and nRF9151 and have a few questions.
1. In regard to modem FOTA delta firmware updates, where is the delta file stored in both Serial...
So in our factory I had setup both an nRF51-DK (PCA10028) and nRF52-DK (PCA10040) to program our external boards we are producing which has a NRF51822-QFAB-R7 populated on...