This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I am having issues programming my nrf5340dk through VSCode or the nrfjprog tools. I have tried as many remedies I can find on the DevZone but not of them seem to correct my...
I am getting an occasional softdevice assert on a BLE central device (hub). Both the central and peripheral devices are nRF52840 using Coded PHY and NCS v2.7.0. This error...
When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
I'm working on an Android app that connects to a Nordic nRF52833 BLE peripheral (Zephyr 3.7.99 / NCS 2.9.0). I'm encountering a consistent issue where:
The app connects...
I am using:
NCS 3.0.1 nRF52840DK
My project is based on the coap_client sample, currently running on a nRF52840DK. I have modified it to add the 'observe' option in the...
I have been following this tutorial by Nordic trying to install nrfConnect for VS Code, nRF Connect for VS Code, part 3: Building an application , but I am facing several...
The VSCode nRF Kconfig extension has very high cpu usage (2 cores at 100%)
When disabling the extension, the cpu usage drops back to normal.
I see the following in the...
I'm planning to build a project using the Nordic Thingy:91X. My goal is to collect sensor data (e.g., environmental or motion sensors) from the device and transmit it over...
Hello
I'm trying to use LittleFS with an external SPI flash, but if the SPI flash isn't available yet at boot time, my application hangs for an uncertain amount of time...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
Hi, Is there any resource or sample project to print the thingy:91x onboard sensor values to the serial using the printk? I tried myself with
#define BME680_NODE DT_NODELABEL...
