Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
Hi, all
My nRF52840 board is running in the extended advertising mode.
My Android phone can scan it, but my iPhone X can't scan it.
I know that iPhone...
I have installed nRF connect for desktop .In which I am trying to connect nRF 52 DK through programmer software. As soon as I connect the development kit via USB to type B...
I'm trying a project (nrf52) where I use both twi and spi to communicate with a set of sensors (each with a different protocol (twi, spi). after enablling TWI0 and SPI0 I...
Hi,
I've been trying to run the examples of the pc-ble-driver-py library, but I can't get them to run.
Every example gives me the following error: Please specifiy connectivity...
Hi team,
I am building AWS IoT client based on NRF52833 + Ethernet Controller.
I have done connecting and subscribing/publishing to AWS IoT broker successfully, and...
Hi there,
I am trying to set up a BLE communication between a central and a peripheral. For this I have succesfully used the nRF RSCS example from Nordic. But the problem...
hi dev
I'm not sure about beacon, so I'm posting questions to check.
General Ble process is like that
1) peripheral do advertise. during advertising interval, it sends...
Hello,
I was using NCS 1.7.0 and developed MQTT and SPI slave based sensor monitoring system using nRF9160 and want to switch NCS to latest build (2.2.0). A whole lot of...
Hello
Im traying to test the csense drv example , I want touch pad button only one
if I want to use this configuration
put the USE_COMP == 0 to USE_COMP == 1
now...
Hi,
We are working on creating a custom board configuration for ease of development. This is based on UBlox BMD-350-EVAL10. Which uses nRF52832.
While I created a custom...
Hi, I am trying to measure a sensor once a second. I require to use oversampling to get 14bits of resolution to meet our target. We are observing a large step in values that...
Dear all,
so far, for my external SPI NAND Flash memory chip development (Micron 256MB SLC NAND), I have been writing and reading data with my own, very basic level, flash...
I'm getting this error when I try to init the UART:
I have app_uart.c in the project, but a little investigation shows that it's not "enabled" in sdk_config.h.
When...
My current project is based on nRF52810. The nRF Connect SDK I found gives the idea that the architecture only works with GCC, according to the link https://developer.nordicsemi...
