Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I am working on implementing a BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED advertising setup.
I would like to minimize the current spike transients...
Hi Team We are working on NFC for our new product. When we measure the power level each GPIO we don't reach more than 700mv. Changing the antenna to a larger antenna did not...
Hello,
I have enabled NRF_LOG over RTT but I get flooded by the same message until my application crashed.
For example:
I get continuously:
what am I doing...
Hello List,
First some context: I am working with SDK 17.1.0 on a nrf52840 (arduino nano ble).
Created a variant of the ble_app_uart example and want to add pairing/bonding...
Hi,
I am aware, that I the PDK is deprecated and I plan to use a nRF5340-DK in the near future.
However, I would like to make use of the PDK I have sitting around and...
Dear Mate,
I am trying to build and flash a program by using (+) Add DFU support to your application - Software - nRF Connect SDK guides - Nordic DevZone (nordicsemi.com...
Dear all,
I'm using nRF52832 and using timers to turn on/off GPIOs.
I saw that timer0, 1 and 2 has 4 CC registers.
Right now, I'm using timer0 like this:
1) turn...
Hi team,
I have some doubts regarding mcuboot behavior on firmware failure.
1) Consider the situation I have flashed a new image , it will get validate before mcuboot...
Hi,
I'm trying to use XIP on our custom board running a nrf5340 with a different Flash memory than the one on the nrf5340-devkit.
The XIP worked on nrf5340dk, but now...
Hi,
I have an nRF9160 device which is going thru PTCRB cert. We are doing TRP/TIS and nRF9160 won't connect to the Anritsu MT8821C. Basically it tries to connect and just...
I have a working MQTT subscription list, when I add a new topic for subscription my subscribe fails with ENOMEM error -12.
If I remove another topic, I can add new topics...
I am looking for a way to set the TX power in Openthtread using Matter with the current version of the nRF-SDK. It appears I cannot find a solution which is up to date.
Hello, guys.
We are using nRF51822 SoC together with nRF5 v12.3.0 SDK.
According to the nRF51822 memory layout , half of the 256KB flash memory space is taken by the Softdevice...
I am using an Nrf52840 and sdk V14.2.0.
My question is how to compute the battery voltage based on my hardware.
The hardware uses AIN0 to measure.
The hardware has a...
It seems this is a new problem with PCA10059 2.1.0, but not 2.0.0 or 2.0.1 that we previously used.
I use a nrf52-dk to connect its P19 to the SWD pins on the dongle. With...
