Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I have a thingy91 that has been flashed over JLINK which has wiped out the MCUBoot. I'm attempting to get it back using mcumgr. I have mcumgr all setup, but when I run
...
While stating debugging mode or normal mode i didn't pair with any devices after advertise duration in RTT viewer
This error raising [ 00> <error> app: Fatal error ]
and...
Hello Nordic community,
We are a software development team. We can directly work on development kits but as a initiative we are trying to buy SOC and do others steps manually...
As described in the brief spec of nRF 21540：
the nRF21540 improves the RX sensitivity by 5 dBm to -100 dBm.
5dBm should be 5dB，you can't make a simple plus/minus equation...
Hi,
I'm doing a Bluetooth test for the nrf52840. However, RF-PHY/TRM-LE/CA/BV-13-C cannot be tested. This means that the instrument does not provide results. The measuring...
Hello,
I want to supply the nRF52832 with a power supply of 2.2Vdc. The uC has to measure an analog voltage between 0 to 2.5V using the internal reference.
Is it possible...
I am trying to set up usb cdc and use the virtual COM port for logging. Please find my code below.
Issue - The LED part of the code works fine but when dongle is connected...
Hi,
I'm testing a prototype with the nRF52840 where I drive a buzzer in the following way:
When I play a signal, I see that the current through the buzzer is about...
Dear everyone,
I'm new to Zigbee and Nordic development. I'm currently working on Zigbee on nrf52833. I must implement a mesh topology to prove self-healing and self-routing...
Hello Nordic team,
I'm looking for some help about Thread creation ... I try to start a Thread when my nrf52840 receive a particular message. This message is sent with BLE...
I am working with the nRF5340 development board. I got the multicore example from the SDK to build without an issue. I then copied the source code and CMake scripts into a...
Trying to get the entire set of v2.0.0 software development tools to install on our Ubuntu 20.04.4 LTS x86_64 system for my nRF9160-DK.
Following the [DevAcademy nRF Connect...
Hi Team,
I am using nRF52810 gpio to power gate (gpio connected to VIN) ADXL362 . But the ADXL362 recommends a switch(SHUTDOWN) as shown below to discharge the capacitors...
Are there any plans for updating the internal CoAP buffer sizes to support 511 OpenThread children? There are two cases where the number of maximum OpenThread children is...
