Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
Hello,
I'm using an NRF5340 with SDK V1.9.1.
I have a code that toggle one gpio pin on a custom board. It is working well when I use P0.22. However, when I change to P0...
Hi all I have a problem with the sim card on our custom board. Earlier I tested my code on nrf9160dk. But on the custom board, the sim card is not recognized. There is no...
We have an nRF5340 application that builds fine for our custom board. However, it is not very straightforward what steps need to be performed to enable FOTA updates. I have...
I am trying to use DTM to evaluate the output filter on our NRF52840 design. I am using the constant output mode and assume that the physical layer setting is not necessary...
Hey guys,
Recently I have been working with the nrf 52840 dongle and my goal is to use the dongle to communicate with a sensor and read values from it. So far I have been...
Hello,
I'm working on development of custom board based of nrf52811, we are using MAXM86161 and ICM-42605 on the custom board but couldn't find any drivers or library...
Hi, The attached picture below captures all the RSSI of our beacons in the field. These devices were set to transmit at maximum transmit power of +4dBm. This max value was...
Hi
I'm trying to get the application timer working on nrf52840 SDK version 17.02
I have followed the below link
devzone.nordicsemi.com/.../application-timer-tutorial...
I am able to print out to Uart but not able to receive from uart.
what do i get wrong?
/* main.c - Application main entry point */
/*
* Copyright (c) 2015-2016...
Hi everyone,
I would like to overwrite my SoftDevice wchich I don't use in my application. I found information about updates without Softdevice.
Its possible to update...
Hi,
I'm trying to build the SLM application on the SIAA chip (w/o GPS). I'm modifying from the nrf9160df_nrf9160 board, but no success there. Is it possible to build the...
When I set the GPIOE pin to float, NRF_DRV_gPIote_IN_config_t config = GPIOTE_CONFIG_IN_SENSE_TOGGLE(true);
The power difference between true and false is 10uA, but when...
Hi All
I have been successfully using a jlink flasher for quite a few years now but after upgrading the segger drivers as i have always done ever couple of months i now...
Dear Nordic Developer Zone,
Is there a way to set the LFCLK (32.768kHz) on a GPIO using nRF52811 ?
I want to use this clock for controlling another device.
Best reg...
