Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hello,
I am developing a door lock system. Where in final product door lock will be controlled and monitored by BLE+Zigbee. So far I have complete success of controlling...
Hi, I'm developing an application using UARTE to reading response from Module Sim. The content response from Module Sim has 495 characters. When I debug, I only read some...
Hi.
I am developing nRF52832 and ST7789.
I'm trying to print out the text, but it's not working properly.
The nrf_gfx_screen_fill() function works fine.
When I proceed...
Hi
I can't set CommonName in the attributes list while generating a private key, it gives an error:
Omitting CN it works fine:
What am I doing wrong?
Thanks...
Hi
I have a question concerning AOA.
I have already make a tx (with nrf52833) and a rx (nrf52833 too) and i succeed to receive the CTE and the IQ sampling with the antenna...
Hello ,
my team and i we are trying to set a communication by UART between two nrf52840 µC , with one of the µC we have done a communication with a nucleo board which supports...
Hello all,
I have made a simple app that runs in loop on the nRF52DK, in general it reads data from the sensor via twi and turns on the leds ...
When the program is run...
Hi, i am developing Zigbee window covering device on nrf connect sdk 1.9.1v which has 2 endpoints, but i am face issue when zigbee command is received and
device_interface_cb...
I have Ebyte’s E73-2G4M08S1C (nrf52840-QIAAC0/ aQFN73 module) where P0.19, P0.21 and P0.23 are not wired out :(
So, my question is which other pins could use / not use instead...
Hi,
I have started learning nRF5340 recently and have got the development kit as well.
I compiled first example of "peripheral_uart" but I am not able to program the board...
I have the ble_peripheral blinky example running, and I have a separate project with the USBD working fine (based on the usbd_cdc_acm example), but when I try to merge the...
The advtising data is 050501020304.That mean
advlen=0x05,
advtype=0x05,//BLE_GAP_AD_TYPE_32BIT_SERVICE_UUID_COMPLETE
advdata=01020304.
we want to set the 32-bit...
Dear Nordic Engineers
I use the NCS V1.9.1.I would like to building the openthread\coprocessor project on the nrf52840_dongle.I read this page: https://developer.nordicsemi...
Hi,
I found that runing a piece of code costs 490.21 us when OpenThread is disabled.
However, after OpenThread is enabled, the time changed to 746.3 us as shown in the...
