Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I'm working from the https://github.com/Martinsbl/nrf5-mpu-examples/tree/sdk13/nrf52-mpu-easydma-using-gpiote-and-registers example and the DMA portion is working splendidly...
I am trying to build the nRF Connect SDK project "at_client" that is provided with the IDE. I also tried the asset_tracker project with a similiar result.
This is my first...
i use a thread to save fil like below ,and find can not save file in sd card ,sd card SPI test ok . before enter in loop. close fil and reset system can save fil in sd card...
The first bug : I believe that the target level argument for the definition of the transition callback should be of type int16_t instead of the unsigned version since it is...
I'm trying to add a sensor driver to my project based off of Zephyr's sensor driver for adxl372. I can't figure out how to get the Kconfig file in that sensor folder to show...
Hi Nordic team,
I'm struggling with an issue where my chip wakes immediately after calling sd_app_evt_wait() - specifically if I call app_timer_start() before the wait for...
Hello, We are looking for production automated current measurement using your product Power Profiler Kit II. Is it possible to interface product using serial/commandline/python...
I wonder if anyone else has seen this issue. There are a few posts that seem to point to using nrfjprog to restore the board, albeit for nRF52. But nothing I have tried allows...
I need to do batch DFU updates, and the pc-ble-driver/nRF Connect Firmware combo is too unreliable for my needs. I would prefer to just use the wireless transciever built...
Hello,
I am using SDK 17.0.2 and want to use Memory Manager Diagnostics .
I have added to my project's sdk_config.h the following :
#ifndef MEM_MANAGER_ENABLE_DIAGNOSTICS...
Hello community,
I have been working on nRF BLE module. I want to make a project that has a small relay control for an appliance. The device will be connected to a mobile...
Hello guys, the USB controller of nRF5340 requires a voltage on VBUS pin.
1. Can nRF5340 be damaged if VBUS voltage rises into its valid range while the device OFF (VDD...
Hi,
I am using NRF52840 development kit and using s140 softdevice for bluetooth services. When I load the softdevice hex file and later load the Firmware hex file, I am...
