Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hello! I`m developing custom board with NRF52832-QFAA on board and need to use serial bootloader. As in example (secure_dfu_ble_s132_pca10040), I`ve implemented it on board...
Peripheral doesn't have any user interface that can be used for pairing and bonding but I want for my application is that the peripheral gets paired or bonded to the central...
I want to make one mesh beacon as a node of mesh network.
If one mesh beacon is a node of mesh network, I want the beacon broadcast the messages which in mesh network to...
I build some test project in Zephyr examples folder. (ncs\v1.5.1\zephyr\samples\basic\ND_test).
In additional I did some changes in the Zephyr project in drivers and added...
I have recntly purchased a Nordic Semiconductors nrf52840 development board. I am having issues with the J Link OB MSD. When connected to LINUX Ubuntu 20.04 LTS which is running...
Hi,
I am working on a bootloader that can do DFU for my nrf52840 DK. Currently, when the bootloader goes into DFU mode, it obtains the init packet via UART. Then, after...
Hi,
I'm trying to add the secure BLE bootloader(non debug, modified to run with S113, SDK 17.0.2) on a custom board with a nRF52810. I tried to DFU my main application(APP...
i working nrf52832 sdk 16 in that i want to use two uart?
actually nrf52832 have only one hardware interfced UART.but i try to implement two UART1 and UART2 in same program...
Hello,
I am working on an nRF52840 with S140SD chip.
I am currently using the RTT as a backend for logs. I tried adding the Flashlog backend in order to save the logs...
I'm developing with nRF52811 but firmware is developed for nRF52810.
I think there is no difference between them and that firmware should work well.
But SPIS doesn't work...
THis may have an obvious answer to an experienced embedded programmer but I do not qualify to be that. So I have a piece of working code that runs on the nRF52840 DK and it...
Can you use/link both nfc T4T and T2T libraries and wrapper/driver source in same application/build?
I don't mean emulating both modes at the same time.
Thanks.
To the kind attention of Nordic support team,
I have been using nRF ble sniffer successfully, it is a great tool. But I have some troubles when it comes to use it for ble...
Hi there!
I am placing variables in the ".non_init" section so that their values are retained across software resets. This works great if I only use an App + Soft Device...
