Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
after I could not use the nRF9160 DK I bought almost a year ago in Germany due to the missing nb-iot coverage I was very curious about the Thingy91 and I assumed...
Sorry for a noob questions but it is essential at this moment as I have not done any development on NordicSemi chips.
What software and hardware tools I need to develop...
Hi,
I am developing a PC SW that connects to nRF52840 device throw a BLE USB dongle(another nRF52840)
How I can tell from PC that a device is connected\disconnected...
Hi,
I use nRF9160 custom board and my application uses USART, ADC, I2c, SPI, RTC and LTE modem. Currently I am trying to reduce sleep current on IDLE state which is 850...
I am going to use nRF52833 chip with SDK v16.0.0 and SoftDevice s140.
There are couple of questions I would like to clarify:
1. Is AoA/AoD direction finding supported...
Hi
Using the nrf52840-dk with SD S140 and nrfx_gpiote, everything runs fund (BLE, TWI etc) but interrup on pin 0,28 causes a Hard Fault. I can not get any sensible logs...
I am trying to modify the existing Thingy-52 code to have a 'new' characteristic. I used the existing Thingy code to 'clone' a new characteristic (a 2nd microphone channel...
Hi
We tested the idle feature(by AT#XSLEEP=0) on nRF9160DK, but no significant change of power consumption before and after enter into IDLE mode, is this result correct...
Hello, I would like to save a log in the nrf5340 FLASH, how many times is possible to write? May I write in the Application CPU Flash from the Network CPU FLASH when the Application...
Hello
I am trying to discover the correct scan interval/window settings to capture the advertized packets from a beacon transmitting every 100ms(10Hz).
Should I just set...
Hello! I've have been designing a custom board. The circuit reads ADC channel 1 for long periods, 1 hour at most. When the reading is high enough it will send an alert using...
Hello,
I am trying to build a remote control using NRF52832 SoC, SDK16.0.0 with softdevice S132 version 7, Keil 5.
I have to control a servo motor and i want to achieve...
Hello,
I need to send logged sensor data in external 4MB flash to a phone via BLE.
I am using a nRF52840 based module on a custom PCB. I am using SDK v14.2.
I am using...
Hello,
Is it possible to get access to the information contained on the SIB (System Information Block) in the nrf9160? if yes, is it through the nRF Connect v3.3.0?
Thanks...
