But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Good day,
I received my nRF52840 kit. Wandering if anyone can guide me in the right direction as to which example/s I should use to be able to implement uart over BLE as...
We have a customer getting the following error message when working with Laird BL652 (nRF52832): NRF_FAULT: id=\01 pc=0x442dc info=323743 .
Please advise what this NRF_Fault...
Hi,
I will come back to the discussion in (because it is in state "Verified Answer" I opened up a new one) :
https://devzone.nordicsemi.com/f/nordic-q-a/55197/nrf52832...
Hello All,
I am looking for a simple example which can handle GPIO interrupt on an event. Is there anything of that sort? Or the API is documented somewhere?
I am using...
i have been trying to interface the imu sensor gy-80 with nrf52840dk
but an error of on the reference main
and the thumb set instructions no memory set errors are comming...
Hi all,
I am doing some development on nRF52840 board with PCA10056.
SDK version: nRF5_SDK_15.3.0
Softdevice: s140_nrf52_6.1.1_softdevice
Testing Example: nRF5_SDK_15...
Hello
in our concurrent radio application using timeslot API there are failed assertions from time to time (10min - 10h).
Message is as above.
Stacktrace and system...
Hi,
I would like to know how much memory my application is consuming. We are using NRF SDK-15.3 version.
In View menu there is option Memory Usage, but when I build in...
Hello,
I am trying connect with the nRF52840 dongle from my android phone using nRF Connect App. The nRF52840 dongle as peripheral and I am using nRF SDK 15.20 and s140_nRF52_6...
Hi,
I have a mesh device (door sensor) with cell battery powered.
When triggered, the device power on, do mesh stack init and start mesh stack, publish a mesh message...
Hello all, is it possible to wake-up the device from deep sleep using cap sense.
How reliable is the ADC cap sense, Im little confused as some people say CapSense is not...
There is an "error" in the Mesh 4.00 friend.c:friendship_alloc(..) function, when allocating a new friend with PollTimeout greater than 2147 seconds. The LPN allows you to...
Hi,
Working with Uart + DMA on the nrf91 board, we see two issues:
1. With baudrate of 115200, we get an overrun error after getting ~6KB of data.
2. Sometimes we do...
