Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I have a QFN48 nRF52832, and it's getting hot. I'm looking at it with a thermal camera and there's a hot spot directly under the "N" of the "N52832" that's on the package...
The BLE_NUS_C_EVT_DISCONNECTED of the ble_nus_c_evt_handler() give a conn_handle = BLE_CONN_HANDLE_INVALID . So it's not possible to know which peripheral got disconnected...
Hi everyone !!
I'm a beginner in ble mesh. I'm working with nRF 52840. I'm not being able to figure out how to see log messages. I want to know where will following line...
Is there anywhere I can find some high level documentation on the FDS module? I'm going thru the API documentation but it provides very little insight into how to best setup...
Hi Nordic Devzone,
First i want to make sure that if the clock being used by softdevice is the LFCLK (32kHz) and its counter register is 24bits ? and which prescaler is...
Hi Guys!
I am a newbee to develop a BLE IoT, and I am really trapped:
first of all: I am using the UART example from the SDK (12.2)
I'd like to send a float array with...
Has anyone been able to successfully connect a BLE device to nRF Cloud using an Android device as a gateway?
I don't see many posts or discussions around this topic. After...
Hi,
I am developing an application, in which I need to store the data collected from various sensors in external flash, in a particular format (Dataset no. - Sensor1 data...
When I use sniffers and wireshark for debugging (ble_app_uart), I found a strange place.
The following are the empty data PDUs seen from wireshark:
50ms:
Master-...
Hi,
I want to use battery service in my beacon for that i have tried two examples of sdk14 on nrf52 dk
1)ble_app_hrs
2)ble_app_proximity
in first example ble_app_hrs...
Hi,
I am nrf52832 SDK14 .
Can you provide a simple example of IRK implementation to resolve the peripheral address in SDK 14.It will be helpful to get insight of it. ...
Hi,
Do you know why I get a warning : Unable to allocate memory for relay packet. ?
I am trying to mesh 2 servers and 4 clients. with client capacity 3 for each server...
Hi,
I'm trying to run the gdb on the nRF52 with softdevice s132 and in the begining it runs ok but after some time when I run (gdb) list I get: "Line number 435 out of...
Hello,
I'd like to send 16 bits data over ble instead of 8 bits
gatts_value.offset = 0;
gatts_value.len = len;
gatts_value.p_value = data;
err_code = sd_ble_gatts_value_set...
The call to ble_x_handles_assign() is not uniformized on all the examples. It's sometime call from on_ble_evt() or/and from x_evt_handler() .
From the doc on the function...