But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi
I have set the nRF Beacon app to action a Tasker task when the phone is "At the beacon".
The app display the following: "An error occurred when launching the task"...
hello
i am using nrf52 board.is there any tutorial to setup the Template project in Visual GDB for the custom design project.i alread test the blinky and the result was successfull...
Hello
I am using this tutorial blog.blecentral.com/.../
to configure my BLENANO to work on eclipse whith gcc toolchain.
I am using the latest SDK which has the softdevice...
Hello,
I can't solved a problem with advertising problem on my iBeacon working on nRF51822.
I have my own 40 unity BLE Module in my room test. They're configured to...
Hello,I run the program nRF52_SDK_11.0.0\examples\peripheral\uart\pca10040\arm4
and rewrite the "main":
int main(void)
{
//LEDS_CONFIGURE(LEDS_MASK);
//LEDS_OFF(LEDS_MASK...
Hi,
nRF5_SDK_11.0.0_89a8197\examples\peripheral\saadc\pca10040\arm5_no_packs
Which timer is used in this example? RTC timer or Timer0-4 ?
I can not find it.
Thanks...
Hi,
I have used nRF51 DK board for 6 months well.
Then now, it isn't connected with nRFgoStudio since I have upgraded nRFgoStudio about 1 month ago.
Error message is no...
Is there any reason I can't have the radio notification run at priority 0? By definition it will never run at the same time as the lower stack, so it seems like I should be...
hi nordic
Have a code project sample shows the typical use Flash applications in data storage?
I see
[code]( infocenter.nordicsemi.com/index.jsp .
my code
`
#define...
If I have a high-priority interrupt (or a series of them) that runs long enough to completely mask a radio notification, then all further radio notifications appear inverted...
I bought two EZAIRO 7150 SL hybrid board, (which contains a MOTHERBOARD & DAUGHTERBOARD). As part of the problems we have been having trying to establish a wireless connection...
Hi, I am developing a software that connects to nRF51822 over UART. I donot have the physical device currently so I downloaded its Soft device under the impression that it...
Hi,I update my MDK from 4.7 to 5.0,my old project can open ,but can't find the device list.I want to use 5.0 and 4.7 at the same time,and I have installed the SDK6.0 when...
Hi, when I compile my project the linker gives me the following error:
._build\nrf51422_xxac_s130.axf: Error: L6200E: Symbol GPIOTE_IRQHandler multiply defined (by app_gpiote_fast_detect...