Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
I am trying to define a simple output pin.
in the DTS file I have:
aliases {
ledred = &hwledred;
ledgreen = &hwledgreen;
memwp = &hwmemwp;
};
soc {
gpio0...
LE audio demo,i enable CONFIG_STREAM_BIDIRECTIONAL ,when i connected Galaxy Buds3 by cis.
my uart_tx will stop.cpu looks busy.when disconnect with headset.data will...
Hello, I have a problem trying to connect Direct Test Mode desktop app to my custom board running Zephyr on nRF52833. My firmware sample is based on hci_uart https://github...
Hi folks,
I've been trying to use the sw_pwm to generate two PWM outputs. I'm using sw_pwm because I want to achieve lower frequencies (1-100Hz) and the hardware PWM API...
Hello,
I need to connect the Thingy:91 to an MCU via UART and/or SPI bus. I need help to identify the pins for communications for:
SPI: CSK, CS, MISO, and MOSI
UART...
Hi, I am new to working on the display . I am trying to integrate nrf5340dk board with waveshare lcd module which is of 1.14 inch and has st7789v controller by using SPI communication...
Hi,
Legacy SDK bootloader and dfu preparation workflow had the following option:
hw_option allowed for checks, whether supplied firmware matches given hardware. So firmware...
Using nrf5340 audio DK & ncs v2.60
I modify this function to print this information when the number of packages reaches 100.
\
Part of the result:
120*100*8/(...
Hi, I'm trying to implement timer synchronization on one central and multiple peripherals, I'm using nRF52840 and NCS v2.8.0. I've seen the example conn_time_sync which uses...
Hi,
I am using download client for downloading a file.
I am using download_client_get and get fragments in callback.
When the file requested is short in the callback...
Hello Nordic Team,
I'm developing a project with two nRF52/nRF54 microcontrollers where I need: - 1st microcontroller as BLE peripheral receiving mobile app data (nRF connect...
I'm migrating code from ncs 2.7 to 2.9.
I am using CONFIG_BT_EXT_ADV and scan timeout callback - such timeout requires CONFIG_BT_EXT_ADV:
It was working fine. Now it's...
Hi,
I follow the custom board exercise steps with mynRF52840 DK and when I reach step 8.1 , in the deviceTree visual editor, I notice that the GPIO0/1/TE options under ...
Hi, I recently updated from NCS 2.6.0 to NCS 2.9.0 which had lots of changes. I believe I ported from child_image to sysbuild with success, as my main application on app core...
