I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
According to data sheet of nRF52832, internal pull up resistance is 13kohm. Can we find the 13kohm internal pull up resistance in the code and can we change that internal...
Ideally we should not get any data when internal pull up resistors of nRF52832 board are disabled and external pull up resistors of SHT 40 Slave sensor are disabled. But I...
Hi,
I haven't been able to actually find out if the VBUS can be used to drive the DETECT signal to go from system off to on mode.
Are there any examples on how to configure...
Hello All, We have designed a custom board for our product and everything pretty much works fine. But now that we have decided to stick to WebBLE, we are facing some issues...
Hi,
I would like to declare my pin in output open-drain, so i use this configuration
My issue is when i declare my pin, I have an unexpected low state that occur...
Hi, I am currently getting started with the Thingy: 91 and am having trouble getting the SDK setup.
I download the file from: https://www.nordicsemi.com/-/media/Software...
1) Our device uses NRF52832 to connect with Android 7 system，use wireshark to monitoring，find not hop，is OK？ and wireshark delta time is Connection Interval ?
2) nrf52832...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
Hi,
I want to monitor the connection state of my device as I have observed situations in which the callback functions defined with bt_conn_cb_register is not fired, causing...
Hi
I have build a sample project nRF5430_audio for nRF5340 Auido DK(two DK, one for gateway, one for headset), following the guide: nRF5340 Audio — nRF Connect SDK 2.0.99...
Hi,
I´m working on a project to send measurement data over ble and receive it. This worked for me, but I want to send the message in my own struct.
What I found in the...
I am trying to use blesniffer on wireshark. I have 2 nRF52840 dongles.
I have successfully captured traces using the 802.15.4 firmware on Wireshark with the dongle appearing...
Hello, I want to know if a typical 50ma Maximum DC-DC converter ic is up to the job of powering up the nrf52840 device working under the heaviest load?
I can't seem to...
Hi Devzone
currently i am doing some test on example central_and_peripheral_hr.
in the orignal example central_and_peripheral_hr is using the BT_SCAN_TYPE_SCAN_PASSIVE...
Hi,
I have a simple question: how to get the link key of nrf5340 audio dk when streaming as gate and handset; we want to catch the airtrace.
BR
Zhongsan
