Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hello All,
SDK -- 15.3.0
I want to interface MX25r6435f with NRF52810 so i saw some older queries regarding this Flash driver,
so some where i saw that in sdk QSPI example...
Hi!
We are working with the nrf5340 (custom board-revision QKAAAB) and we are facing an issue when resetting the application. If we add some functionalities to a bluetooth...
hello,
i am using nrf52832 with sdk 15.2 and i want to advertise my beacon like the above picture how can i change the length type and values i can understand the app beacon...
Once paired & Bonding is completed. If neither side pairing & Bonding information is deleted. After restart the device is not advertising again. We are getting PM_EVT_CONN_SEC_FAILED...
Hi, Good afternoon. Some Questions.
1.
Is the Enhanced ShockBurst (ESB) protocol applicable to the nRF5340? I'd appreciate it if you could give me details on how to get...
The nrf52833_peripherals.h file has the P1_PIN_NUM set to 10 but the pca10100.h file has ARDUINO 8-13 pins mapped to port 1, pin 17 to 23. This cannot be correct and causes...
Hey all,
I want to try the Asset Tracker v2 (NCS v1.6.0) Application in AWS, so I followed this guide .
When I try to create the CA certificates and register them in AWS...
Hi,
I'm trying to build the smp_svr example for Thingy:52 but build fails when linking.
I can build for the nrf52dk_nrf52832 which uses the same chip. What can i do to...
Dear Nordic Team,
We have a running product that is using 32KHZ quartz from MicroCrystal : https://www.microcrystal.com/fileadmin/Media/Products/32kHz/Datasheet/CM7V-T1A...
Hello,
I have a design where I am using an nRF52840 along with a SKY66112-11 and am using Zephyr/MPSL for both BLE and Thread. I also have a run-time radio test mode which...
Hi, I have installed the most recent version of nRF toolchain manager for windows (V0.9.2). nRF SDK V1.6.0 was released a couple of days ago but it is (not yet?) in the list...
I am new to BLE.
My question is similar to the one below.
https://devzone.nordicsemi.com/f/nordic-q-a/22596/nrf51822-central-connect-and-communicate-with-2-peripherals...
I am using the nfc_writable_ndef_msg example in the SDK to write from my phone to the board using NFC. I get it working successfully however, I am also trying to add code...
