Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I developed a custom RF mesh to USB serial bridge. Right after boot, I receive all serial messages, but once the host closes the serial port and open it again, nothing comes...
I use BSD socket to send and receive messages to a TCP server over LTE network.
When I send multiple messages by using send() (with flags = 0) function, I get an EINPROGRESS...
I am curious if anyone can point me to an example of working with the SRP functionality in the CryptoCell.
I see the headers for it at nrfxlib/crypto/nrf_cc310_mbedcrypto...
Hi,
I try to create an MQTT AGPS tracker.
I'm using a nrf9160dk with the 1.3.0v.
I use two threads, one for GPS (A-GPS) and one other to send value to MQTT (witch starts...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0).
To set the transmit power for advertisement, I am using sd_ble_gap_tx_power_set...
We are planing to use nrf52840 sdk in our project.we want to use mesh stack for that.
our product is sensor:
-deployed in oil field.
- send data 8 times a day.
-payload...
Hi,
I'm developing on nRF51422 board and I'm currently adding BLE security just work feature based on SDK12.3.0 using softdevice s130_2.0.1(nRF is used as BLE peripheral...
Hi
Past week (on a Windows 10 pc) I've installed the nrf connect sdk (nrfconnectsetup331ia32), and yesterday offered me an update (nrfconnectsetup340ia32); since I've not...
Hi, I encountered the problem of losing data in uart serial port when using ble_app_uart_pca10040_s132 example.
sdk 16.0.0, s132, 7.0.1, nrf52832,
APP_ADV_DURATION=0,...
I want to connect two nrf52840 device and raspberry pi. When connecting to a single device, it works fine. However, when connecting with two devices, an error occurs and stops...
Hello all,
I am interested in using the Secure Serial Bootloader to program my NRF52832 over UART from an external MCU. I am aware of the SDK example and creating DFU...
I have a system that will have multiple ways of doing DFU. BLE, as normal, UART under special circumstances, and a "no transport" way. In the latter I will have transported...
Hi guys,
I was working on my nRF5340 based custom board. From a certain point on the nRF5340 stopped to accept any command from J-Link (SWD link). For example, in response...
I Separate two projects ,SPM application and non-secure application.the spi driver can work in non-secure application,when I try to transplant the spi driver in SPM application...
Hi,
We are using nRF52840 in HV mode and VDD is configured for 1.8v. By mistake, we have connected VDDH to one of the GPIOs as input. What are the implications? How much...
