This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi
I have lost my private key for generating my dfu pakage using nrfutil.
I have 2K nrf Modules chips already programmed with bootloader & dfu enabled firmware. However...
Hello,
I'm having a weird problem while doing a communication between nRF52840( perpherial device ) with USB OTG ( STM32 ).
I'm trying send out the data from USB OTG...
Hi,
We have a production device using the NRF9160 and after several days end up triggering a __bus_fault() that arises likely from memory fragmentation in the heap within...
Hello all.
i am trying to flash a boot loader with arduino IDE. i got the technique from here : https://github.com/sandeepmistry/arduino-nRF5
after doing all steps i am...
We upgrade to the latest Mesh SDK 4.0 but the light server example is behaving differently. We have our own code from an iOS app that provisions the device.
After I provisioning...
Using 840DK and latest Segger (4.42)
Building Mesh DFU example: dfu_nrf52840_xxAA_s140_7_0_1
Latest Mesh SDK v4
Latest SDK 16
Build with no errors, when starting debug...
I want to use the random number API for nRF5340APPLICATION. But I can only choose TEST_RANDOM_GENERATOR. And can not use sys_csrand_get().
How to use RandomAPI for nRF5340Application...
I'm using React Native and the BLE package react-native-ble-plx on my Ubuntu machine.
According to the docs, I've done the following: 1. Scanned for devices 2. Connected...
I have just started the BLE _tempelate project and I came across the BLE_GAP_EVT_PHY_UPDATE_REQUEST case.
I could not find many details about it. Can anyone explain what...
Hi,
We are looking for help with the Nordic nRF-Mesh Library software. We want to create a react-native nRF-Mesh library for IOS and Android. We can see that the example...
Hi,
I am trying to turn on p0.03 when it goes in dfu mode but it not turning on
err_code = nrf_drv_gpiote_init(); APP_ERROR_CHECK(err_code); nrf_drv_gpiote_out_config_t...
Hi everyone,
I am testing the NRF9160 DK and I want to test the low power mode.
I found and tried the solution detailled in this blog about how to measure PSM idle current...
Hi,
I am using nrf52840 controller . I need to transfer the data using Bluetooth at 10ms by using application timer and i am using SDK 15.3 version and soft device S140...
Hello, i have question: How nRF Connect SDK gets MAC addresses Steps: 1. I build android ble peripheral app and starting advertaising. When i did it, MAC address alwalse random...
