Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
hello,
I am using SDK16 ble_app_gls example . I set static passkey with adding this code in ble_stack_init function.
When I write password "123456" I can connect on nrf...
Hi
This question is related to sd_ble_gap_keypress_notify() . According to Nordic softdevice S132 v3.0.0 API:-
"This function can only be used when an authentication...
Hi
I am currently working on calculating the AoA. I have 4 nRF52833 DKs and I am using three DKs as transmitters and one as the receiver and the receiver is connected to...
This page https://www.nordicsemi.com/Software-and-Tools/Development-Kits/nRF52840-DK/GetStarted says " If step 4) below fails, you need to re-program the factory example code...
How can I calculate max and average power of this chip? During use, I intend to be at 0dB TX and 1 Mbs data rate with a 3V supply. I am going to guess the max power draw will...
Hello everyone
I am using nRF52 DK PCA10040.
I try to generate puls by Timer 0.
The puls width is 400ns.
This goal was failed.
---------------------------------...
I'm struggling to get buttonless DFU to work with FreeRTOS. I've gotten buttonless DFU sample to run on the hardware. I also have FreeRTOS running on the hardware. However...
Hello,
I need to remap ble bootloader because I want to use nrf52832_AB instead of nrf52832_AA found in dev kits.
I wish I could have this memory mapping in embedded flash...
Viewers! Don't click on a similar issue or you will lose everything you have done!
Calling this method sd_ble_gatts_characteristic_add(...) with a characteristic value...
Dear all,
Im trying to interface LIS3DH with the following code, and drivers of LIS2DH (LIS3DH and LIS2DH have the almost same hardware and config.)
I have included...
It seems there is hardware support for NB2, but the modem firmware isn't there yet.
What's the timeline on this? And if a precise time isn't available, is it in the order...
Hi!
I know, that there are some similar issues in this forum, and I checked them, but I didn't see the clue.
I try to use fstorage to write something to flash. I have...
After many hours of successful LTE connections and using the AF_LTE socket just fine (many creates, many send/receive, many closes), my application now hangs on a call to...
Hi What is the ADC frequency range and operation at nRF52833 ? we are interfacing the TUSS4470 with nRF52833 ,WITH SPI communication . is that the frequency range supports...
